Steel 1330 Normalized vs 1330 Q&T
Steel · 1330 temper comparison
1330 Normalized and 1330 Q&T are two conditions of the same steel grade, 1330: Normalized versus Q&T (quenched and tempered). The chemistry is identical, so every difference below comes from the condition. 1330 Q&T is the stronger of the two: yield strength 830 MPa (120 ksi) against 560 MPa (81.2 ksi) for 1330 Normalized, about 48% more; tensile strength follows at 910 MPa (132 ksi) vs 835 MPa (121 ksi). In exchange, 1330 Normalized is the more ductile: elongation 22% versus 18% for 1330 Q&T, and 1330 Q&T is harder (263 HB vs 248 HB).
1330 NormalizedChoose it when the part is bent, formed or impact-loaded.
1330 Q&TChoose it when strength drives the design.
1330 Normalized vs 1330 Q&T: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 205 GPa29.7 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,425°C2,597 °F · Liquidus Temperature 1,500°C2,732 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.2 µm/m·K6.8 µin/in·°F · Latent Heat of Fusion 250 J/g107 BTU/lb · Min Service Temperature -30°C-22 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.62 V · Corrosion Resistance 11 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 55 / 100 · Polishability 55 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 25 MJ/kg10,748 BTU/lb · Embodied Carbon (primary production) 2 kg CO₂/kg · Embodied Water 45 L/kg5.4 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
1330 Normalized vs 1330 Q&T — frequently asked
Is 1330 Q&T stronger than 1330 Normalized?
Yes. 1330 Q&T has a typical yield strength of 830 MPa (120 ksi) against 560 MPa (81.2 ksi) for 1330 Normalized — about 48% more. Tensile strength is 910 MPa (132 ksi) vs 835 MPa (121 ksi).
Which condition does FabDigit quote by default, Normalized or Q&T?
HR is the default 1330 condition in the FabDigit quote flow (neither Normalized nor Q&T). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose 1330 Normalized over 1330 Q&T?
Pick 1330 Normalized when the part is bent, formed or impact-loaded. Pick 1330 Q&T when strength drives the design.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 1330 Normalized and 1330 Q&T side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.