Steel 1330 Annealed vs 1330 Normalized
Steel · 1330 temper comparison
1330 Annealed and 1330 Normalized are two conditions of the same steel grade, 1330: Annealed versus Normalized. The chemistry is identical, so every difference below comes from the condition. 1330 Normalized is the stronger of the two: yield strength 560 MPa (81.2 ksi) against 470 MPa (68.2 ksi) for 1330 Annealed, about 19% more; tensile strength follows at 835 MPa (121 ksi) vs 705 MPa (102 ksi). In exchange, 1330 Annealed is the more ductile: elongation 25.5% versus 22% for 1330 Normalized, and 1330 Normalized is harder (248 HB vs 207 HB).
1330 AnnealedChoose it when the part is bent, formed or impact-loaded.
1330 NormalizedChoose it when strength drives the design.
1330 Annealed vs 1330 Normalized: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 205 GPa29.7 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29 · Charpy V-Notch Impact (RT) 90 J66.4 ft·lbf
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,425°C2,597 °F · Liquidus Temperature 1,500°C2,732 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Same in both: Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.2 µm/m·K6.8 µin/in·°F · Latent Heat of Fusion 250 J/g107 BTU/lb · Max Service Temperature (continuous) 400°C752 °F · Min Service Temperature -30°C-22 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.62 V · Corrosion Resistance 11 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 55 / 100 · Polishability 55 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 25 MJ/kg10,748 BTU/lb · Embodied Carbon (primary production) 2 kg CO₂/kg · Embodied Water 45 L/kg5.4 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
1330 Annealed vs 1330 Normalized — frequently asked
Is 1330 Normalized stronger than 1330 Annealed?
Yes. 1330 Normalized has a typical yield strength of 560 MPa (81.2 ksi) against 470 MPa (68.2 ksi) for 1330 Annealed — about 19% more. Tensile strength is 835 MPa (121 ksi) vs 705 MPa (102 ksi).
Which condition does FabDigit quote by default, Annealed or Normalized?
HR is the default 1330 condition in the FabDigit quote flow (neither Annealed nor Normalized). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 1330 Annealed or 1330 Normalized?
1330 Annealed, by a small margin. Both rate good for machinability — 62/100 against 56/100 for 1330 Normalized; for welding the order is 1330 Annealed first (fair, 48/100) then 1330 Normalized (fair, 42/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 1330 Annealed and 1330 Normalized side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.