Stainless Steel SUH1-CD vs SUH1-QT
Stainless Steel · SUH1 temper comparison
SUH1-CD and SUH1-QT are two conditions of the same stainless steel grade, SUH1: CD (cold drawn) versus QT (quenched and tempered). The chemistry is identical, so every difference below comes from the condition. SUH1-QT is the stronger of the two: yield strength 760 MPa (110 ksi) against 620 MPa (89.9 ksi) for SUH1-CD, about 23% more; tensile strength follows at 1,000 MPa (145 ksi) vs 860 MPa (125 ksi). SUH1-QT is the more ductile: elongation 18% versus 14% for SUH1-CD, and SUH1-QT is harder (295 HB vs 265 HB). SUH1-QT runs hotter in service (750°C vs 550°C continuous) and SUH1-CD conducts heat better (24.5 W/m·K vs 21 W/m·K).
SUH1-QTChoose it when strength drives the design, or when the part is bent, formed or impact-loaded.
SUH1-CD vs SUH1-QT: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 215 GPa31.2 Msi · Shear Modulus 83 GPa12 Msi · Bulk Modulus 165 GPa23.9 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.7 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,420°C2,588 °F · Liquidus Temperature 1,480°C2,696 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 480 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 11 µm/m·K6.1 µin/in·°F · Latent Heat of Fusion 260 J/g112 BTU/lb · Min Service Temperature -20°C-4 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.45 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 40 / 100 · Brazeability / Solderability 35 / 100 · Polishability 60 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 52 MJ/kg22,356 BTU/lb · Embodied Carbon (primary production) 3.5 kg CO₂/kg · Embodied Water 110 L/kg13.2 gal/lb · Typical Recycled Content 60%
Strength versus weight
Yield strength against density for every stainless steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
SUH1-CD vs SUH1-QT — frequently asked
Is SUH1-QT stronger than SUH1-CD?
Yes. SUH1-QT has a typical yield strength of 760 MPa (110 ksi) against 620 MPa (89.9 ksi) for SUH1-CD — about 23% more. Tensile strength is 1,000 MPa (145 ksi) vs 860 MPa (125 ksi).
Which condition does FabDigit quote by default, CD or QT?
QT is the default SUH1 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, SUH1-CD or SUH1-QT?
SUH1-CD, by a small margin. Both rate fair for machinability — 42/100 against 35/100 for SUH1-QT.
Ready to make it?
Upload a CAD file and FabDigit prices the part in SUH1-CD and SUH1-QT side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.