Stainless Steel S41041 Annealed vs S41041 Q&T
Stainless Steel · S41041 temper comparison
S41041 Annealed and S41041 Q&T are two conditions of the same stainless steel grade, S41041: Annealed versus Q&T (quenched and tempered). The chemistry is identical, so every difference below comes from the condition. S41041 Q&T is the stronger of the two: yield strength 590 MPa (85.6 ksi) against 280 MPa (40.6 ksi) for S41041 Annealed, about 111% more; tensile strength follows at 760 MPa (110 ksi) vs 450 MPa (65.3 ksi). In exchange, S41041 Annealed is the more ductile: elongation 30% versus 18% for S41041 Q&T, and S41041 Q&T is harder (245 HB vs 150 HB).
S41041 AnnealedChoose it when the part is bent, formed or impact-loaded.
S41041 Q&TChoose it when strength drives the design.
S41041 Annealed vs S41041 Q&T: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 200 GPa29 Msi · Shear Modulus 78 GPa11.3 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29 · Reduction in Area 65% · Compressive Strength 280 MPa40.6 ksi · Shear Strength 290 MPa42.1 ksi · Hardness, Rockwell B 80 HRB
Physical
Density and transition temperatures.
Same in both: Density 7.7 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,480°C2,696 °F · Liquidus Temperature 1,530°C2,786 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 25 W/m·K14.4 BTU/hr·ft·°F · Specific Heat Capacity 460 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 10.5 µm/m·K5.8 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Max Service Temperature (continuous) 650°C1,202 °F · Min Service Temperature -30°C-22 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 3 % IACS · Electrical Resistivity 5.7×10⁻⁷ Ω·m22.4 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.3 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability Rating (AISI 1212 = 100 %)
Formability (cold)
Same in both: Machinability 50 / 100 · Weldability 72 / 100 · Castability 45 / 100 · Brazeability / Solderability 55 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 42 MJ/kg18,057 BTU/lb · Embodied Carbon (primary production) 3.2 kg CO₂/kg · Embodied Water 140 L/kg16.8 gal/lb · Typical Recycled Content 70%
Strength versus weight
Yield strength against density for every stainless steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
S41041 Annealed vs S41041 Q&T — frequently asked
Is S41041 Q&T stronger than S41041 Annealed?
Yes. S41041 Q&T has a typical yield strength of 590 MPa (85.6 ksi) against 280 MPa (40.6 ksi) for S41041 Annealed — about 111% more. Tensile strength is 760 MPa (110 ksi) vs 450 MPa (65.3 ksi).
Which condition does FabDigit quote by default, Annealed or Q&T?
Annealed is the default S41041 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose S41041 Annealed over S41041 Q&T?
Pick S41041 Annealed when the part is bent, formed or impact-loaded. Pick S41041 Q&T when strength drives the design.
Ready to make it?
Upload a CAD file and FabDigit prices the part in S41041 Annealed and S41041 Q&T side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.