Precious Metal 92Ag-8SnO2-H04 vs 92Ag-8SnO2 PM-EXT
Precious Metal · 92Ag-8SnO2 temper comparison
92Ag-8SnO2-H04 and 92Ag-8SnO2 PM-EXT are two conditions of the same precious metal grade, 92Ag-8SnO2: H04 (full hard) versus PM-EXT (as-sintered / extruded). The chemistry is identical, so every difference below comes from the condition. 92Ag-8SnO2-H04 is the stronger of the two: yield strength 275 MPa (39.9 ksi) against 140 MPa (20.3 ksi) for 92Ag-8SnO2 PM-EXT, about 96% more; tensile strength follows at 325 MPa (47.1 ksi) vs 245 MPa (35.5 ksi). In exchange, 92Ag-8SnO2 PM-EXT is the more ductile: elongation 15% versus 4% for 92Ag-8SnO2-H04, and 92Ag-8SnO2-H04 is harder (90 HB vs 65 HB). 92Ag-8SnO2 PM-EXT runs hotter in service (200°C vs 150°C continuous). On the shop floor, 92Ag-8SnO2-H04 machines more easily (good vs fair).
92Ag-8SnO2-H04Choose it when strength drives the design, or when the part is machined in volume.
92Ag-8SnO2 PM-EXTChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
92Ag-8SnO2-H04 vs 92Ag-8SnO2 PM-EXT: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all precious metal grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all precious metal grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
92Ag-8SnO2-H0492Ag-8SnO2 PM-EXT
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Shear Strength
Hardness, Brinell
Hardness, Vickers
Same in both: Shear Modulus 32 GPa4.6 Msi · Bulk Modulus 105 GPa15.2 Msi · Poisson's Ratio 0.37
Physical
Density and transition temperatures.
Same in both: Density 10.1 g/cm³0.36 lb/in³ · Melting Point (Solidus) 961°C1,762 °F · Liquidus Temperature 961°C1,762 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 240 J/kg·K0.06 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 19 µm/m·K10.6 µin/in·°F · Latent Heat of Fusion 100 J/g43 BTU/lb · Min Service Temperature -200°C-328 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) 0.05 V · Corrosion Resistance 88 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 85 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 1,450 MJ/kg623,388 BTU/lb · Embodied Carbon (primary production) 110 kg CO₂/kg · Embodied Water 2,000 L/kg240 gal/lb · Typical Recycled Content 40%
Strength versus weight
Yield strength against density for every precious metal grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
92Ag-8SnO2-H04 vs 92Ag-8SnO2 PM-EXT — frequently asked
Is 92Ag-8SnO2-H04 stronger than 92Ag-8SnO2 PM-EXT?
Yes. 92Ag-8SnO2-H04 has a typical yield strength of 275 MPa (39.9 ksi) against 140 MPa (20.3 ksi) for 92Ag-8SnO2 PM-EXT — about 96% more. Tensile strength is 325 MPa (47.1 ksi) vs 245 MPa (35.5 ksi).
Which condition does FabDigit quote by default, H04 or PM-EXT?
O is the default 92Ag-8SnO2 condition in the FabDigit quote flow (neither H04 nor PM-EXT). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 92Ag-8SnO2-H04 or 92Ag-8SnO2 PM-EXT?
92Ag-8SnO2-H04. Its machinability rates good (55/100) against fair (42/100) for 92Ag-8SnO2 PM-EXT; for welding the order is 92Ag-8SnO2-H04 first (poor, 25/100) then 92Ag-8SnO2 PM-EXT (poor, 20/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 92Ag-8SnO2-H04 and 92Ag-8SnO2 PM-EXT side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.