Digital ABS vs MED610
Polymer · grade comparison
Digital ABS and MED610 are both polymer grades. Digital ABS is the more ductile: elongation 30% versus 17% for MED610. Digital ABS is stiffer (2.8 GPa vs 2.5 GPa) and Digital ABS runs hotter in service (50°C vs 45°C continuous). On the shop floor, MED610 sits in a lower cost tier (high, $$$$) than Digital ABS (specialty, $$$$$).
Digital ABSChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
MED610Choose it when cost is the deciding factor.
Digital ABS vs MED610: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all polymer grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all polymer grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Poisson's Ratio
Elongation at Break
Flexural Strength
Flexural Modulus
Izod Impact, Notched
Hardness, Shore D
Hardness, Rockwell M
Compressive Strength
Same in both: Tensile Strength (Ultimate) 57 MPa8.3 ksi
Physical
Density and transition temperatures.
Glass Transition (Tg)
Water Absorption (24 h)
Water Absorption (Saturation)
Refractive Index
Light Transmission
Same in both: Density 1.18 g/cm³0.04 lb/in³
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Heat Deflection Temp. @ 0.45 MPa
Heat Deflection Temp. @ 1.8 MPa
Thermal Conductivity
Specific Heat Capacity
Thermal Expansion (CTE, 20–100 °C)
Same in both: Min Service Temperature -20°C-4 °F
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
UV / Weathering Resistance
Same in both: Corrosion Resistance 70 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Weldability
Polishability
Processing Melt Temperature (typ.)
Same in both: Machinability 55 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Typical Recycled Content
Common Calculations
Ratios derived from the values above.
Specific Stiffness (E / density)
Same in both: Specific Strength (UTS / density) 49 kN·m/kg
Strength versus weight
Yield strength against density for every polymer grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | Digital ABS | MED610 |
|---|---|---|
| 3D printing | Yes | — |
| Default condition | Standard | — |
| Relative cost | $$$$$ Specialty | $$$$ High |
| Min. machined wall | — | — |
| Best machined surface | — | — |
| Conductive Coating | Yes | — |
| Dyeing (Nylon) | Yes | — |
| EMI Shielding Coating | Yes | — |
| Painting | Yes | — |
| Primer Coating | Yes | — |
| Soft Touch Coating | Yes | — |
| Tinted Coating | Yes | — |
| UV Coating | Yes | — |
| Vacuum Metallization | Yes | — |
| Waterproof Coating | Yes | — |
Digital ABS vs MED610 — frequently asked
What is the difference between Digital ABS and MED610?
Digital ABS and MED610 are both polymer grades. Digital ABS is the more ductile: elongation 30% versus 17% for MED610. Digital ABS is stiffer (2.8 GPa vs 2.5 GPa) and Digital ABS runs hotter in service (50°C vs 45°C continuous).
Which is cheaper, Digital ABS or MED610?
MED610 is the lower-cost material: it sits in the high tier ($$$$) while Digital ABS is specialty ($$$$$). Part price depends far more on geometry, tolerance and quantity than on raw stock — upload a CAD file for a live quote.
When should I choose Digital ABS over MED610?
Pick Digital ABS when the part is bent, formed or impact-loaded, or when the part sees heat. Pick MED610 when cost is the deciding factor.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Digital ABS and MED610 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.