Nickel Alloy ENiCrCoMo-1 vs ERNiCrFe-7
Nickel Alloy · grade comparison
Nickel Alloy ENiCrCoMo-1 and ERNiCrFe-7 are both nickel alloy grades. ENiCrCoMo-1 is the stronger of the two: tensile strength 720 MPa (104 ksi) against 655 MPa (95 ksi) for ERNiCrFe-7, about 10% more. ENiCrCoMo-1 is harder — 210 HB against 185 HB for ERNiCrFe-7 — which matters for wear surfaces and threads. ENiCrCoMo-1 runs hotter in service (1,100°C vs 950°C continuous) and ENiCrCoMo-1 conducts heat better (13.6 W/m·K vs 12 W/m·K). On the shop floor, ERNiCrFe-7 forms better (good vs fair).
ENiCrCoMo-1Choose it when strength drives the design, or when surface hardness matters.
ENiCrCoMo-1 vs ERNiCrFe-7: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Shear Modulus
Bulk Modulus
Poisson's Ratio
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Rockwell C
Hardness, Vickers
Physical
Density and transition temperatures.
Density
Melting Point (Solidus)
Liquidus Temperature
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Thermal Expansion (CTE, 20–100 °C)
Max Service Temperature (continuous)
Same in both: Latent Heat of Fusion 290 J/g125 BTU/lb · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.15 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Weldability
Formability (cold)
Polishability
Same in both: Machinability Rating (AISI 1212 = 100 %) 12% · Brazeability / Solderability 55 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Typical Recycled Content
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Modulus of Resilience
Thermal Diffusivity
Thermal Shock Resistance Index
Strength versus weight
Yield strength against density for every nickel alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | ENiCrCoMo-1 | ERNiCrFe-7 |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$$$ High | $$$$ High |
| Min. machined wall | — | — |
| Best machined surface | — | — |
Both take the same 3 finishes: Gold Plating, Plasma Spray, Silver Plating.
ENiCrCoMo-1 vs ERNiCrFe-7 — frequently asked
Is ENiCrCoMo-1 stronger than ERNiCrFe-7?
Yes. ENiCrCoMo-1 has a typical tensile strength of 720 MPa (104 ksi) against 655 MPa (95 ksi) for ERNiCrFe-7 — about 10% more.
Which is cheaper, ENiCrCoMo-1 or ERNiCrFe-7?
Both sit in the same relative cost tier ($$$$, high); the part price will be decided by machining time, tolerance and quantity rather than by the material.
Which welds better, ENiCrCoMo-1 or ERNiCrFe-7?
ENiCrCoMo-1. Its weldability rates excellent (85/100) against very good (78/100) for ERNiCrFe-7.
Ready to make it?
Upload a CAD file and FabDigit prices the part in ENiCrCoMo-1 and ERNiCrFe-7 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.