Nickel Alloy CZ-100 vs M-35-1
Nickel Alloy · grade comparison
Nickel Alloy CZ-100 and M-35-1 are both nickel alloy grades. M-35-1 is the stronger of the two: yield strength 205 MPa (29.7 ksi) against 160 MPa (23.2 ksi) for CZ-100, about 28% more; tensile strength follows at 485 MPa (70.3 ksi) vs 380 MPa (55.1 ksi). M-35-1 is the more ductile: elongation 35% versus 25% for CZ-100, and M-35-1 is harder (125 HB vs 110 HB). CZ-100 is stiffer (180 GPa vs 150 GPa) and CZ-100 conducts heat better (50 W/m·K vs 22 W/m·K). On the shop floor, M-35-1 welds better (very good vs good).
M-35-1Choose it when strength drives the design, or when the part is bent, formed or impact-loaded.
CZ-100 vs M-35-1: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Shear Modulus
Bulk Modulus
Poisson's Ratio
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Physical
Density and transition temperatures.
Density
Melting Point (Solidus)
Liquidus Temperature
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Thermal Expansion (CTE, 20–100 °C)
Latent Heat of Fusion
Same in both: Max Service Temperature (continuous) 480°C896 °F · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Galvanic Potential (seawater, vs SCE)
Corrosion Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Weldability
Formability (cold)
Castability
Brazeability / Solderability
Polishability
Same in both: Machinability Rating (AISI 1212 = 100 %) 30%
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Typical Recycled Content
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Modulus of Resilience
Thermal Diffusivity
Thermal Shock Resistance Index
Strength versus weight
Yield strength against density for every nickel alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | CZ-100 | M-35-1 |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$$$ High | $$$$ High |
| Min. machined wall | — | — |
| Best machined surface | — | — |
Both take the same 3 finishes: Gold Plating, Plasma Spray, Silver Plating.
CZ-100 vs M-35-1 — frequently asked
Is M-35-1 stronger than CZ-100?
Yes. M-35-1 has a typical yield strength of 205 MPa (29.7 ksi) against 160 MPa (23.2 ksi) for CZ-100 — about 28% more. Tensile strength is 485 MPa (70.3 ksi) vs 380 MPa (55.1 ksi).
Which is cheaper, CZ-100 or M-35-1?
Both sit in the same relative cost tier ($$$$, high); the part price will be decided by machining time, tolerance and quantity rather than by the material.
Which is easier to machine, CZ-100 or M-35-1?
CZ-100. Its machinability rates fair (35/100) against poor (30/100) for M-35-1; for welding the order is M-35-1 first (very good, 72/100) then CZ-100 (good, 60/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in CZ-100 and M-35-1 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.