Magnesium Alloy MA8-HR vs MA8-M
Magnesium Alloy · MA8 temper comparison
MA8-HR and MA8-M are two conditions of the same magnesium alloy grade, MA8: HR (hot rolled) versus M (thermomechanically controlled processed). The chemistry is identical, so every difference below comes from the condition. MA8-HR is the stronger of the two: yield strength 140 MPa (20.3 ksi) against 130 MPa (18.9 ksi) for MA8-M, about 8% more. In exchange, MA8-M is the more ductile: elongation 15% versus 12% for MA8-HR, and MA8-HR is harder (48 HB vs 45 HB).
MA8-HRChoose it when strength drives the design.
MA8-MChoose it when the part is bent, formed or impact-loaded.
MA8-HR vs MA8-M: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all magnesium alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all magnesium alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Same in both: Elastic (Young's) Modulus 43 GPa6.2 Msi · Shear Modulus 16.5 GPa2.4 Msi · Bulk Modulus 45 GPa6.5 Msi · Poisson's Ratio 0.35 · Fracture Toughness (K_IC) 16 MPa·√m14.6 ksi·√in
Physical
Density and transition temperatures.
Same in both: Density 1.78 g/cm³0.06 lb/in³ · Melting Point (Solidus) 648°C1,198 °F · Liquidus Temperature 651°C1,204 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 138 W/m·K79.7 BTU/hr·ft·°F · Specific Heat Capacity 1,050 J/kg·K0.25 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 26 µm/m·K14.4 µin/in·°F · Latent Heat of Fusion 370 J/g159 BTU/lb · Max Service Temperature (continuous) 150°C302 °F · Min Service Temperature -70°C-94 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 34 % IACS · Electrical Resistivity 5.1×10⁻⁸ Ω·m2.01 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -1.6 V · Corrosion Resistance 28 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Weldability
Formability (cold)
Same in both: Machinability 95 / 100 · Machinability Rating (AISI 1212 = 100 %) 400% · Brazeability / Solderability 25 / 100 · Polishability 55 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 330 MJ/kg141,875 BTU/lb · Embodied Carbon (primary production) 30 kg CO₂/kg · Embodied Water 300 L/kg35.9 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every magnesium alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
MA8-HR vs MA8-M — frequently asked
Is MA8-HR stronger than MA8-M?
Yes. MA8-HR has a typical yield strength of 140 MPa (20.3 ksi) against 130 MPa (18.9 ksi) for MA8-M — about 8% more. Tensile strength is 235 MPa (34.1 ksi) vs 240 MPa (34.8 ksi).
Which condition does FabDigit quote by default, HR or M?
M is the default MA8 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose MA8-HR over MA8-M?
Pick MA8-HR when strength drives the design. Pick MA8-M when the part is bent, formed or impact-loaded.
Ready to make it?
Upload a CAD file and FabDigit prices the part in MA8-HR and MA8-M side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.