Magnesium Alloy AM20 vs AS41B
Magnesium Alloy · grade comparison
Magnesium Alloy AM20 and AS41B are both magnesium alloy grades. AS41B is the stronger of the two: yield strength 140 MPa (20.3 ksi) against 90 MPa (13.1 ksi) for AM20, about 56% more; tensile strength follows at 215 MPa (31.2 ksi) vs 195 MPa (28.3 ksi). In exchange, AM20 is the more ductile: elongation 12% versus 6% for AS41B, and AS41B is harder (75 HB vs 45 HB). AS41B runs hotter in service (175°C vs 110°C continuous) and AM20 conducts heat better (100 W/m·K vs 68 W/m·K). On the shop floor, AM20 welds better (50 vs 35 out of 100).
AM20Choose it when the part is bent, formed or impact-loaded, or when it will be welded.
AS41BChoose it when strength drives the design, or when the part sees heat.
AM20 vs AS41B: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all magnesium alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all magnesium alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Compressive Strength
Shear Strength
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 45 GPa6.5 Msi · Shear Modulus 17 GPa2.5 Msi · Bulk Modulus 45 GPa6.5 Msi · Poisson's Ratio 0.35 · Fatigue Strength (Endurance Limit) 70 MPa10.2 ksi
Physical
Density and transition temperatures.
Density
Melting Point (Solidus)
Liquidus Temperature
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Thermal Expansion (CTE, 20–100 °C)
Latent Heat of Fusion
Max Service Temperature (continuous)
Min Service Temperature
Same in both: Specific Heat Capacity 1,020 J/kg·K0.24 BTU/lb·°F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Galvanic Potential (seawater, vs SCE)
Corrosion Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Castability
Brazeability / Solderability
Same in both: Machinability 95 / 100 · Polishability 55 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Same in both: Embodied Water 500 L/kg59.9 gal/lb · Typical Recycled Content 30%
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Modulus of Resilience
Thermal Diffusivity
Thermal Shock Resistance Index
Strength versus weight
Yield strength against density for every magnesium alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | AM20 | AS41B |
|---|---|---|
| CNC machining | — | Yes |
| Default condition | — | As Cast |
| Relative cost | $$ Standard | $$ Standard |
| Min. machined wall | — | 0.8 mm |
| Best machined surface | — | Ra 0.8 µm |
| Anodizing Type II | — | Yes |
| Chem Film (Alodine) | — | Yes |
| E-Coating | — | Yes |
| Hard Anodize Type III w/ PTFE | — | Yes |
| Hard Anodizing Type III | — | Yes |
| Painting | — | Yes |
| Powder Coating | — | Yes |
AM20 vs AS41B — frequently asked
Is AS41B stronger than AM20?
Yes. AS41B has a typical yield strength of 140 MPa (20.3 ksi) against 90 MPa (13.1 ksi) for AM20 — about 56% more. Tensile strength is 215 MPa (31.2 ksi) vs 195 MPa (28.3 ksi).
Which is cheaper, AM20 or AS41B?
Both sit in the same relative cost tier ($$, standard); the part price will be decided by machining time, tolerance and quantity rather than by the material.
Which welds better, AM20 or AS41B?
AM20. Its weldability rates fair (50/100) against fair (35/100) for AS41B.
Ready to make it?
Upload a CAD file and FabDigit prices the part in AM20 and AS41B side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.