Copper Alloy C95500 vs CC331G
Copper Alloy · grade comparison
Copper Alloy C95500 and CC331G are both copper alloy grades. C95500 is the stronger of the two: yield strength 300 MPa (43.5 ksi) against 200 MPa (29 ksi) for CC331G, about 50% more; tensile strength follows at 700 MPa (102 ksi) vs 550 MPa (79.8 ksi). In exchange, CC331G is the more ductile: elongation 25% versus 8% for C95500, and C95500 is harder (192 HB vs 120 HB). CC331G conducts heat better (59 W/m·K vs 42 W/m·K). On the shop floor, CC331G sits in a lower cost tier (high, $$$$) than C95500 (specialty, $$$$$).
C95500Choose it when strength drives the design.
CC331GChoose it when the part is bent, formed or impact-loaded, or when cost is the deciding factor.
C95500 vs CC331G: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Shear Modulus
Bulk Modulus
Poisson's Ratio
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Compressive Strength
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 110 GPa16 Msi
Physical
Density and transition temperatures.
Density
Melting Point (Solidus)
Liquidus Temperature
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Latent Heat of Fusion
Min Service Temperature
Same in both: Thermal Expansion (CTE, 20–100 °C) 16.2 µm/m·K9 µin/in·°F · Max Service Temperature (continuous) 300°C572 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.28 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Weldability
Formability (cold)
Castability
Same in both: Machinability Rating (AISI 1212 = 100 %) 50% · Brazeability / Solderability 30 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Typical Recycled Content
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Modulus of Resilience
Thermal Diffusivity
Thermal Shock Resistance Index
Strength versus weight
Yield strength against density for every copper alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | C95500 | CC331G |
|---|---|---|
| CNC machining | Yes | — |
| Default condition | As Cast | — |
| Relative cost | $$$$$ Specialty | $$$$ High |
| Min. machined wall | 0.8 mm | — |
| Best machined surface | Ra 1.6 µm | — |
| Chrome Plating | Yes | — |
| Electropolishing | Yes | — |
| Nickel Plating | Yes | — |
| Painting | Yes | — |
| Tin Plating | Yes | — |
They share 4 finishes: Copper Plating, Electroless Nickel (EN), Gold Plating, Silver Plating.
C95500 vs CC331G — frequently asked
Is C95500 stronger than CC331G?
Yes. C95500 has a typical yield strength of 300 MPa (43.5 ksi) against 200 MPa (29 ksi) for CC331G — about 50% more. Tensile strength is 700 MPa (102 ksi) vs 550 MPa (79.8 ksi).
Which is cheaper, C95500 or CC331G?
CC331G is the lower-cost material: it sits in the high tier ($$$$) while C95500 is specialty ($$$$$). Part price depends far more on geometry, tolerance and quantity than on raw stock — upload a CAD file for a live quote.
Which is easier to machine, C95500 or CC331G?
CC331G, by a small margin. Both rate fair for machinability — 45/100 against 40/100 for C95500; for welding the order is CC331G first (good, 65/100) then C95500 (good, 60/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in C95500 and CC331G side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.