Titanium Ti-6Al-4V (AM, F2924) vs Ti-6Al-4V (Grade 5) AM Powder
Titanium · grade comparison
Titanium Ti-6Al-4V (AM, F2924) and Ti-6Al-4V (Grade 5) AM Powder are both titanium grades. Both yield at about 1,040 MPa — strength does not separate them.
Ti-6Al-4V (AM, F2924) vs Ti-6Al-4V (Grade 5) AM Powder: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all titanium grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all titanium grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Ti-6Al-4V (AM, F2924)Ti-6Al-4V (Grade 5) AM Powder
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Rockwell C
Same in both: Elastic (Young's) Modulus 113 GPa16.4 Msi · Shear Modulus 44 GPa6.4 Msi · Bulk Modulus 110 GPa16 Msi · Poisson's Ratio 0.34 · Hardness, Brinell 340 HB · Hardness, Vickers 355 HV
Physical
Density and transition temperatures.
Same in both: Density 4.43 g/cm³0.16 lb/in³ · Melting Point (Solidus) 1,604°C2,919 °F · Liquidus Temperature 1,660°C3,020 °F
Thermal
How each material carries heat and how hot it can run.
Latent Heat of Fusion
Min Service Temperature
Same in both: Thermal Conductivity 6.8 W/m·K3.9 BTU/hr·ft·°F · Specific Heat Capacity 526 J/kg·K0.13 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 8.7 µm/m·K4.8 µin/in·°F · Max Service Temperature (continuous) 350°C662 °F
Electrical
Conductivity and insulation.
Electrical Resistivity
Same in both: Electrical Conductivity 1 % IACS
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.1 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Weldability
Formability (cold)
Brazeability / Solderability
Castability
Same in both: Machinability Rating (AISI 1212 = 100 %) 22% · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Typical Recycled Content
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Modulus of Resilience
Same in both: Specific Stiffness (E / density) 25.5 MN·m/kg · Thermal Diffusivity 2.9 mm²/s · Thermal Shock Resistance Index 8
Strength versus weight
Yield strength against density for every titanium grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | Ti-6Al-4V (AM, F2924) | Ti-6Al-4V (Grade 5) AM Powder |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$$$ High | $$$$ High |
| Min. machined wall | — | — |
| Best machined surface | — | — |
Both take the same 1 finish: Plasma Spray.
Ti-6Al-4V (AM, F2924) vs Ti-6Al-4V (Grade 5) AM Powder — frequently asked
What is the difference between Ti-6Al-4V (AM, F2924) and Ti-6Al-4V (Grade 5) AM Powder?
Titanium Ti-6Al-4V (AM, F2924) and Ti-6Al-4V (Grade 5) AM Powder are both titanium grades. Both yield at about 1,040 MPa — strength does not separate them.
Which is cheaper, Ti-6Al-4V (AM, F2924) or Ti-6Al-4V (Grade 5) AM Powder?
Both sit in the same relative cost tier ($$$$, high); the part price will be decided by machining time, tolerance and quantity rather than by the material.
Which welds better, Ti-6Al-4V (AM, F2924) or Ti-6Al-4V (Grade 5) AM Powder?
Ti-6Al-4V (AM, F2924). Its weldability rates good (65/100) against good (60/100) for Ti-6Al-4V (Grade 5) AM Powder.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Ti-6Al-4V (AM, F2924) and Ti-6Al-4V (Grade 5) AM Powder side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.