Titanium Grade Ti-Pd7B-F vs Grade Ti-Pd7B-HIP
Titanium · Grade Ti-Pd7B temper comparison
Grade Ti-Pd7B-F and Grade Ti-Pd7B-HIP are two conditions of the same titanium grade, Grade Ti-Pd7B: F (as fabricated) versus HIP (hot isostatic pressed). The chemistry is identical, so every difference below comes from the condition. Both yield at about 375 MPa — the mechanical properties are the same, and the difference is in how the stock is processed and what it is certified to (as fabricated versus hot isostatic pressed). Grade Ti-Pd7B-HIP is the more ductile: elongation 20% versus 16% for Grade Ti-Pd7B-F.
Grade Ti-Pd7B-HIPChoose it when the part is bent, formed or impact-loaded.
Grade Ti-Pd7B-F vs Grade Ti-Pd7B-HIP: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all titanium grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all titanium grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Grade Ti-Pd7B-FGrade Ti-Pd7B-HIP
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Shear Modulus 39 GPa5.7 Msi · Bulk Modulus 110 GPa16 Msi · Poisson's Ratio 0.34
Physical
Density and transition temperatures.
Same in both: Density 4.51 g/cm³0.16 lb/in³ · Melting Point (Solidus) 1,660°C3,020 °F · Liquidus Temperature 1,670°C3,038 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 16.4 W/m·K9.5 BTU/hr·ft·°F · Specific Heat Capacity 523 J/kg·K0.12 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 8.6 µm/m·K4.8 µin/in·°F · Latent Heat of Fusion 365 J/g157 BTU/lb · Max Service Temperature (continuous) 400°C752 °F · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 3.3 % IACS · Electrical Resistivity 5.2×10⁻⁷ Ω·m20.5 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.08 V · Corrosion Resistance 96 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Same in both: Weldability 85 / 100 · Castability 62 / 100 · Brazeability / Solderability 40 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 750 MJ/kg322,442 BTU/lb · Embodied Carbon (primary production) 46 kg CO₂/kg · Embodied Water 500 L/kg59.9 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every titanium grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Grade Ti-Pd7B-F vs Grade Ti-Pd7B-HIP — frequently asked
What is the difference between Grade Ti-Pd7B-F and Grade Ti-Pd7B-HIP?
Grade Ti-Pd7B-F and Grade Ti-Pd7B-HIP are two conditions of the same titanium grade, Grade Ti-Pd7B: F (as fabricated) versus HIP (hot isostatic pressed). The chemistry is identical, so every difference below comes from the condition. Both yield at about 375 MPa — the mechanical properties are the same, and the difference is in how the stock is processed and what it is certified to (as fabricated versus hot isostatic pressed).
Which condition does FabDigit quote by default, F or HIP?
A is the default Grade Ti-Pd7B condition in the FabDigit quote flow (neither F nor HIP). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose Grade Ti-Pd7B-F over Grade Ti-Pd7B-HIP?
Pick Grade Ti-Pd7B-HIP when the part is bent, formed or impact-loaded.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Grade Ti-Pd7B-F and Grade Ti-Pd7B-HIP side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.