Steel TRIP Steel-HR vs TRIP Steel TRIP590
Steel · TRIP Steel temper comparison
TRIP Steel-HR and TRIP Steel TRIP590 are two conditions of the same steel grade, TRIP Steel: HR (hot rolled) versus TRIP590. The chemistry is identical, so every difference below comes from the condition. TRIP Steel-HR is the stronger of the two: yield strength 460 MPa (66.7 ksi) against 400 MPa (58 ksi) for TRIP Steel TRIP590, about 15% more; tensile strength follows at 750 MPa (109 ksi) vs 630 MPa (91.4 ksi). In exchange, TRIP Steel TRIP590 is the more ductile: elongation 30% versus 24% for TRIP Steel-HR, and TRIP Steel-HR is harder (223 HB vs 190 HB). On the shop floor, TRIP Steel TRIP590 welds better (68 vs 58 out of 100).
TRIP Steel-HRChoose it when strength drives the design.
TRIP Steel TRIP590Choose it when the part is bent, formed or impact-loaded, or when it will be welded.
TRIP Steel-HR vs TRIP Steel TRIP590: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
TRIP Steel-HRTRIP Steel TRIP590
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 205 GPa29.7 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.3
Physical
Density and transition temperatures.
Same in both: Density 7.8 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,450°C2,642 °F · Liquidus Temperature 1,500°C2,732 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Same in both: Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.5 µm/m·K6.9 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Max Service Temperature (continuous) 200°C392 °F · Min Service Temperature -60°C-76 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Same in both: Electrical Resistivity 2.2×10⁻⁷ Ω·m8.66 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.65 V · Corrosion Resistance 10 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 55 / 100 · Polishability 45 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 30 MJ/kg12,898 BTU/lb · Embodied Carbon (primary production) 2.3 kg CO₂/kg · Embodied Water 45 L/kg5.4 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
TRIP Steel-HR vs TRIP Steel TRIP590 — frequently asked
Is TRIP Steel-HR stronger than TRIP Steel TRIP590?
Yes. TRIP Steel-HR has a typical yield strength of 460 MPa (66.7 ksi) against 400 MPa (58 ksi) for TRIP Steel TRIP590 — about 15% more. Tensile strength is 750 MPa (109 ksi) vs 630 MPa (91.4 ksi).
Which condition does FabDigit quote by default, HR or TRIP590?
CR is the default TRIP Steel condition in the FabDigit quote flow (neither HR nor TRIP590). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which welds better, TRIP Steel-HR or TRIP Steel TRIP590?
TRIP Steel TRIP590. Its weldability rates good (68/100) against good (58/100) for TRIP Steel-HR.
Ready to make it?
Upload a CAD file and FabDigit prices the part in TRIP Steel-HR and TRIP Steel TRIP590 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.