Steel SNCM220 Annealed vs SNCM220 Normalized
Steel · SNCM220 temper comparison
SNCM220 Annealed and SNCM220 Normalized are two conditions of the same steel grade, SNCM220: Annealed versus Normalized. The chemistry is identical, so every difference below comes from the condition. SNCM220 Annealed is the stronger of the two: yield strength 385 MPa (55.8 ksi) against 360 MPa (52.2 ksi) for SNCM220 Normalized, about 7% more. SNCM220 Annealed is the more ductile: elongation 31% versus 26% for SNCM220 Normalized, and SNCM220 Normalized is harder (183 HB vs 149 HB).
SNCM220 AnnealedChoose it when strength drives the design, or when the part is bent, formed or impact-loaded.
SNCM220 Annealed vs SNCM220 Normalized: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
SNCM220 AnnealedSNCM220 Normalized
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 205 GPa29.7 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,425°C2,597 °F · Liquidus Temperature 1,505°C2,741 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Same in both: Specific Heat Capacity 475 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 11.6 µm/m·K6.4 µin/in·°F · Latent Heat of Fusion 260 J/g112 BTU/lb · Max Service Temperature (continuous) 400°C752 °F · Min Service Temperature -40°C-40 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.6 V · Corrosion Resistance 12 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 40 / 100 · Brazeability / Solderability 65 / 100 · Polishability 60 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 30 MJ/kg12,898 BTU/lb · Embodied Carbon (primary production) 2.2 kg CO₂/kg · Embodied Water 60 L/kg7.2 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
SNCM220 Annealed vs SNCM220 Normalized — frequently asked
Is SNCM220 Annealed stronger than SNCM220 Normalized?
Yes. SNCM220 Annealed has a typical yield strength of 385 MPa (55.8 ksi) against 360 MPa (52.2 ksi) for SNCM220 Normalized — about 7% more. Tensile strength is 535 MPa (77.6 ksi) vs 630 MPa (91.4 ksi).
Which condition does FabDigit quote by default, Annealed or Normalized?
HR is the default SNCM220 condition in the FabDigit quote flow (neither Annealed nor Normalized). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which welds better, SNCM220 Annealed or SNCM220 Normalized?
SNCM220 Annealed. Its weldability rates good (60/100) against good (55/100) for SNCM220 Normalized.
Ready to make it?
Upload a CAD file and FabDigit prices the part in SNCM220 Annealed and SNCM220 Normalized side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.