Steel SM490-CR vs SM490YB
Steel · SM490 temper comparison
SM490-CR and SM490YB are two conditions of the same steel grade, SM490: CR (cold rolled) versus SM490YB (higher yield class (≥365 MPa) with Charpy ≥27 J at 0 °C). The chemistry is identical, so every difference below comes from the condition. SM490-CR is the stronger of the two: yield strength 480 MPa (69.6 ksi) against 405 MPa (58.7 ksi) for SM490YB, about 19% more; tensile strength follows at 600 MPa (87 ksi) vs 545 MPa (79 ksi). In exchange, SM490YB is the more ductile: elongation 21% versus 14% for SM490-CR, and SM490-CR is harder (185 HB vs 172 HB). SM490YB runs hotter in service (350°C vs 300°C continuous).
SM490-CRChoose it when strength drives the design.
SM490YBChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
SM490-CR vs SM490YB: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Shear Modulus 79 GPa11.5 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.3
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,425°C2,597 °F · Liquidus Temperature 1,505°C2,741 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Min Service Temperature
Same in both: Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12 µm/m·K6.7 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb
Electrical
Conductivity and insulation.
Electrical Conductivity
Same in both: Electrical Resistivity 2×10⁻⁷ Ω·m7.87 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.62 V · Corrosion Resistance 11 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Polishability
Same in both: Brazeability / Solderability 60 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 25 MJ/kg10,748 BTU/lb · Embodied Carbon (primary production) 2.1 kg CO₂/kg · Embodied Water 30 L/kg3.6 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
SM490-CR vs SM490YB — frequently asked
Is SM490-CR stronger than SM490YB?
Yes. SM490-CR has a typical yield strength of 480 MPa (69.6 ksi) against 405 MPa (58.7 ksi) for SM490YB — about 19% more. Tensile strength is 600 MPa (87 ksi) vs 545 MPa (79 ksi).
Which condition does FabDigit quote by default, CR or SM490YB?
HR is the default SM490 condition in the FabDigit quote flow (neither CR nor SM490YB). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, SM490-CR or SM490YB?
SM490-CR. Its machinability rates good (62/100) against fair (53/100) for SM490YB.
Ready to make it?
Upload a CAD file and FabDigit prices the part in SM490-CR and SM490YB side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.