Steel P195GH +AR vs P195GH +C
Steel · P195GH temper comparison
P195GH +AR and P195GH +C are two conditions of the same steel grade, P195GH: +AR (hot rolled) versus +C (cold drawn). The chemistry is identical, so every difference below comes from the condition. P195GH +C is the stronger of the two: yield strength 370 MPa (53.7 ksi) against 235 MPa (34.1 ksi) for P195GH +AR, about 57% more; tensile strength follows at 460 MPa (66.7 ksi) vs 390 MPa (56.6 ksi). In exchange, P195GH +AR is the more ductile: elongation 28% versus 12% for P195GH +C, and P195GH +C is harder (150 HB vs 115 HB). P195GH +AR runs hotter in service (400°C vs 300°C continuous).
P195GH +ARChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
P195GH +CChoose it when strength drives the design.
P195GH +AR vs P195GH +C: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Shear Modulus 81 GPa11.7 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,470°C2,678 °F · Liquidus Temperature 1,520°C2,768 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 461 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12 µm/m·K6.7 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Min Service Temperature -20°C-4 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.65 V · Corrosion Resistance 10 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 65 / 100 · Polishability 45 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 25 MJ/kg10,748 BTU/lb · Embodied Carbon (primary production) 2 kg CO₂/kg · Embodied Water 60 L/kg7.2 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
P195GH +AR vs P195GH +C — frequently asked
Is P195GH +C stronger than P195GH +AR?
Yes. P195GH +C has a typical yield strength of 370 MPa (53.7 ksi) against 235 MPa (34.1 ksi) for P195GH +AR — about 57% more. Tensile strength is 460 MPa (66.7 ksi) vs 390 MPa (56.6 ksi).
Which condition does FabDigit quote by default, +AR or +C?
+N is the default P195GH condition in the FabDigit quote flow (neither +AR nor +C). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, P195GH +AR or P195GH +C?
P195GH +C, by a small margin. Both rate good for machinability — 64/100 against 56/100 for P195GH +AR; for welding the order is P195GH +AR first (excellent, 95/100) then P195GH +C (excellent, 88/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in P195GH +AR and P195GH +C side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.