Steel MS1300-CR vs MS1300 CR-TEMPERED
Steel · MS1300 temper comparison
MS1300-CR and MS1300 CR-TEMPERED are two conditions of the same steel grade, MS1300: CR (cold rolled) versus CR-TEMPERED (CR). The chemistry is identical, so every difference below comes from the condition. Both yield at about 1,150 MPa — the mechanical properties are the same, and the difference is in how the stock is processed and what it is certified to (cold rolled versus CR). MS1300 CR-TEMPERED is the more ductile: elongation 6% versus 5% for MS1300-CR. MS1300 CR-TEMPERED runs hotter in service (250°C vs 200°C continuous).
MS1300 CR-TEMPEREDChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
MS1300-CR vs MS1300 CR-TEMPERED: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 207 GPa30 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.3
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,450°C2,642 °F · Liquidus Temperature 1,510°C2,750 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 34 W/m·K19.6 BTU/hr·ft·°F · Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12 µm/m·K6.7 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Min Service Temperature -40°C-40 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 7.8 % IACS · Electrical Resistivity 2.2×10⁻⁷ Ω·m8.66 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.6 V · Corrosion Resistance 10 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 40 / 100 · Polishability 45 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 30 MJ/kg12,898 BTU/lb · Embodied Carbon (primary production) 2.3 kg CO₂/kg · Embodied Water 45 L/kg5.4 gal/lb · Typical Recycled Content 20%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
MS1300-CR vs MS1300 CR-TEMPERED — frequently asked
What is the difference between MS1300-CR and MS1300 CR-TEMPERED?
MS1300-CR and MS1300 CR-TEMPERED are two conditions of the same steel grade, MS1300: CR (cold rolled) versus CR-TEMPERED (CR). The chemistry is identical, so every difference below comes from the condition. Both yield at about 1,150 MPa — the mechanical properties are the same, and the difference is in how the stock is processed and what it is certified to (cold rolled versus CR).
Which condition does FabDigit quote by default, CR or CR-TEMPERED?
CR is the default MS1300 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose MS1300-CR over MS1300 CR-TEMPERED?
Pick MS1300 CR-TEMPERED when the part is bent, formed or impact-loaded, or when the part sees heat.
Ready to make it?
Upload a CAD file and FabDigit prices the part in MS1300-CR and MS1300 CR-TEMPERED side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.