Steel CRS-CD vs CRS-CR
Steel · CRS temper comparison
CRS-CD and CRS-CR are two conditions of the same steel grade, CRS: CD (cold drawn) versus CR (cold rolled). The chemistry is identical, so every difference below comes from the condition. CRS-CD is the stronger of the two: yield strength 370 MPa (53.7 ksi) against 220 MPa (31.9 ksi) for CRS-CR, about 68% more; tensile strength follows at 440 MPa (63.8 ksi) vs 340 MPa (49.3 ksi). In exchange, CRS-CR is the more ductile: elongation 38% versus 15% for CRS-CD, and CRS-CD is harder (130 HB vs 95 HB). On the shop floor, CRS-CD machines more easily (68 vs 58 out of 100).
CRS-CDChoose it when strength drives the design, or when the part is machined in volume.
CRS-CRChoose it when the part is bent, formed or impact-loaded.
CRS-CD vs CRS-CR: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Hardness, Brinell
Hardness, Rockwell B
Same in both: Elastic (Young's) Modulus 200 GPa29 Msi · Shear Modulus 79 GPa11.5 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29 · Compressive Strength 220 MPa31.9 ksi · Fracture Toughness (K_IC) 120 MPa·√m109 ksi·√in · Charpy V-Notch Impact (RT) 90 J66.4 ft·lbf · Hardness, Vickers 100 HV
Physical
Density and transition temperatures.
Same in both: Density 7.87 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,495°C2,723 °F · Liquidus Temperature 1,528°C2,782 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 52 W/m·K30 BTU/hr·ft·°F · Specific Heat Capacity 480 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.2 µm/m·K6.8 µin/in·°F · Latent Heat of Fusion 272 J/g117 BTU/lb · Max Service Temperature (continuous) 400°C752 °F · Min Service Temperature -20°C-4 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 12 % IACS · Electrical Resistivity 1.43×10⁻⁷ Ω·m5.63 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.62 V · Corrosion Resistance 10 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 75 / 100 · Polishability 35 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 25 MJ/kg10,748 BTU/lb · Embodied Carbon (primary production) 2.1 kg CO₂/kg · Embodied Water 50 L/kg6 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
CRS-CD vs CRS-CR — frequently asked
Is CRS-CD stronger than CRS-CR?
Yes. CRS-CD has a typical yield strength of 370 MPa (53.7 ksi) against 220 MPa (31.9 ksi) for CRS-CR — about 68% more. Tensile strength is 440 MPa (63.8 ksi) vs 340 MPa (49.3 ksi).
Which condition does FabDigit quote by default, CD or CR?
HR is the default CRS condition in the FabDigit quote flow (neither CD nor CR). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, CRS-CD or CRS-CR?
CRS-CD, by a small margin. Both rate good for machinability — 68/100 against 58/100 for CRS-CR.
Ready to make it?
Upload a CAD file and FabDigit prices the part in CRS-CD and CRS-CR side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.