Steel 4063-A vs 4063-HR
Steel · 4063 temper comparison
4063-A and 4063-HR are two conditions of the same steel grade, 4063: A (solution annealed) versus HR (hot rolled). The chemistry is identical, so every difference below comes from the condition. 4063-HR is the stronger of the two: yield strength 540 MPa (78.3 ksi) against 420 MPa (60.9 ksi) for 4063-A, about 29% more; tensile strength follows at 950 MPa (138 ksi) vs 730 MPa (106 ksi). In exchange, 4063-A is the more ductile: elongation 22% versus 14% for 4063-HR, and 4063-HR is harder (280 HB vs 210 HB). 4063-HR runs hotter in service (400°C vs 200°C continuous).
4063-AChoose it when the part is bent, formed or impact-loaded.
4063-HRChoose it when strength drives the design, or when the part sees heat.
4063-A vs 4063-HR: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 205 GPa29.7 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29 · Charpy V-Notch Impact (RT) 20 J14.8 ft·lbf
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,400°C2,552 °F · Liquidus Temperature 1,470°C2,678 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 475 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 11.5 µm/m·K6.4 µin/in·°F · Latent Heat of Fusion 250 J/g107 BTU/lb · Min Service Temperature -40°C-40 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.62 V · Corrosion Resistance 10 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 35 / 100 · Polishability 65 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 31 MJ/kg13,328 BTU/lb · Embodied Carbon (primary production) 2.3 kg CO₂/kg · Embodied Water 45 L/kg5.4 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
4063-A vs 4063-HR — frequently asked
Is 4063-HR stronger than 4063-A?
Yes. 4063-HR has a typical yield strength of 540 MPa (78.3 ksi) against 420 MPa (60.9 ksi) for 4063-A — about 29% more. Tensile strength is 950 MPa (138 ksi) vs 730 MPa (106 ksi).
Which condition does FabDigit quote by default, A or HR?
OQT425 is the default 4063 condition in the FabDigit quote flow (neither A nor HR). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 4063-A or 4063-HR?
4063-A, by a small margin. Both rate fair for machinability — 50/100 against 45/100 for 4063-HR; for welding the order is 4063-HR first (poor, 20/100) then 4063-A (poor, 15/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 4063-A and 4063-HR side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.