Steel 11MnNi5-3 +N (30-50 mm) vs 11MnNi5-3 +QT
Steel · 11MnNi5-3 temper comparison
11MnNi5-3 +N (30-50 mm) and 11MnNi5-3 +QT are two conditions of the same steel grade, 11MnNi5-3: +N (30-50 mm) (+N) versus +QT (quenched and tempered). The chemistry is identical, so every difference below comes from the condition. 11MnNi5-3 +QT is the stronger of the two: yield strength 380 MPa (55.1 ksi) against 310 MPa (45 ksi) for 11MnNi5-3 +N (30-50 mm), about 23% more; tensile strength follows at 510 MPa (74 ksi) vs 455 MPa (66 ksi). 11MnNi5-3 +QT is harder — 165 HB against 145 HB for 11MnNi5-3 +N (30-50 mm) — which matters for wear surfaces and threads.
11MnNi5-3 +QTChoose it when strength drives the design, or when surface hardness matters.
11MnNi5-3 +N (30-50 mm) vs 11MnNi5-3 +QT: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
11MnNi5-3 +N (30-50 mm)11MnNi5-3 +QT
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Same in both: Elastic (Young's) Modulus 210 GPa30.5 Msi · Shear Modulus 81 GPa11.7 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29 · Reduction in Area 58%
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,460°C2,660 °F · Liquidus Temperature 1,515°C2,759 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Same in both: Specific Heat Capacity 460 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 11.8 µm/m·K6.6 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Max Service Temperature (continuous) 350°C662 °F · Min Service Temperature -60°C-76 °F
Electrical
Conductivity and insulation.
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Corrosion Resistance 12 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 55 / 100 · Polishability 50 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 26 MJ/kg11,178 BTU/lb · Embodied Carbon (primary production) 2 kg CO₂/kg · Embodied Water 45 L/kg5.4 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
11MnNi5-3 +N (30-50 mm) vs 11MnNi5-3 +QT — frequently asked
Is 11MnNi5-3 +QT stronger than 11MnNi5-3 +N (30-50 mm)?
Yes. 11MnNi5-3 +QT has a typical yield strength of 380 MPa (55.1 ksi) against 310 MPa (45 ksi) for 11MnNi5-3 +N (30-50 mm) — about 23% more. Tensile strength is 510 MPa (74 ksi) vs 455 MPa (66 ksi).
Which condition does FabDigit quote by default, +N (30-50 mm) or +QT?
+N is the default 11MnNi5-3 condition in the FabDigit quote flow (neither +N (30-50 mm) nor +QT). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 11MnNi5-3 +N (30-50 mm) or 11MnNi5-3 +QT?
11MnNi5-3 +N (30-50 mm), by a small margin. Both rate good for machinability — 66/100 against 60/100 for 11MnNi5-3 +QT.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 11MnNi5-3 +N (30-50 mm) and 11MnNi5-3 +QT side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.