Stainless Steel S34565-CD vs S34565-F49
Stainless Steel · S34565 temper comparison
S34565-CD and S34565-F49 are two conditions of the same stainless steel grade, S34565: CD (cold drawn) versus F49 (forged and solution annealed). The chemistry is identical, so every difference below comes from the condition. S34565-CD is the stronger of the two: yield strength 700 MPa (102 ksi) against 450 MPa (65.3 ksi) for S34565-F49, about 56% more; tensile strength follows at 950 MPa (138 ksi) vs 830 MPa (120 ksi). In exchange, S34565-F49 is the more ductile: elongation 40% versus 25% for S34565-CD, and S34565-CD is harder (280 HB vs 215 HB).
S34565-CDChoose it when strength drives the design.
S34565-F49Choose it when the part is bent, formed or impact-loaded.
S34565-CD vs S34565-F49: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Same in both: Elastic (Young's) Modulus 190 GPa27.6 Msi · Shear Modulus 73 GPa10.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.3
Physical
Density and transition temperatures.
Same in both: Density 8 g/cm³0.29 lb/in³ · Melting Point (Solidus) 1,350°C2,462 °F · Liquidus Temperature 1,400°C2,552 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 11.5 W/m·K6.6 BTU/hr·ft·°F · Specific Heat Capacity 490 J/kg·K0.12 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 14.5 µm/m·K8.1 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 1.9 % IACS · Electrical Resistivity 9.2×10⁻⁷ Ω·m36.2 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.1 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 50 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 78 MJ/kg33,534 BTU/lb · Embodied Carbon (primary production) 5.8 kg CO₂/kg · Embodied Water 120 L/kg14.4 gal/lb · Typical Recycled Content 45%
Strength versus weight
Yield strength against density for every stainless steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
S34565-CD vs S34565-F49 — frequently asked
Is S34565-CD stronger than S34565-F49?
Yes. S34565-CD has a typical yield strength of 700 MPa (102 ksi) against 450 MPa (65.3 ksi) for S34565-F49 — about 56% more. Tensile strength is 950 MPa (138 ksi) vs 830 MPa (120 ksi).
Which condition does FabDigit quote by default, CD or F49?
SA is the default S34565 condition in the FabDigit quote flow (neither CD nor F49). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose S34565-CD over S34565-F49?
Pick S34565-CD when strength drives the design. Pick S34565-F49 when the part is bent, formed or impact-loaded.
Ready to make it?
Upload a CAD file and FabDigit prices the part in S34565-CD and S34565-F49 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.