Stainless Steel 305 Annealed vs 305 Cold Drawn
Stainless Steel · 305 temper comparison
305 Annealed and 305 Cold Drawn are two conditions of the same stainless steel grade, 305: Annealed versus Cold Drawn. The chemistry is identical, so every difference below comes from the condition. 305 Cold Drawn is the stronger of the two: yield strength 430 MPa (62.4 ksi) against 260 MPa (37.7 ksi) for 305 Annealed, about 65% more; tensile strength follows at 655 MPa (95 ksi) vs 585 MPa (84.8 ksi). In exchange, 305 Annealed is the more ductile: elongation 50% versus 32% for 305 Cold Drawn, and 305 Cold Drawn is harder (200 HB vs 150 HB).
305 AnnealedChoose it when the part is bent, formed or impact-loaded.
305 Cold DrawnChoose it when strength drives the design.
305 Annealed vs 305 Cold Drawn: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Bulk Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 193 GPa28 Msi · Shear Modulus 77 GPa11.2 Msi · Poisson's Ratio 0.29 · Compressive Strength 260 MPa37.7 ksi · Fracture Toughness (K_IC) 220 MPa·√m200 ksi·√in
Physical
Density and transition temperatures.
Density
Same in both: Melting Point (Solidus) 1,400°C2,552 °F · Liquidus Temperature 1,450°C2,642 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Expansion (CTE, 20–100 °C)
Same in both: Thermal Conductivity 16.2 W/m·K9.4 BTU/hr·ft·°F · Specific Heat Capacity 500 J/kg·K0.12 BTU/lb·°F · Latent Heat of Fusion 285 J/g123 BTU/lb · Max Service Temperature (continuous) 760°C1,400 °F · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 2.4 % IACS · Electrical Resistivity 7.2×10⁻⁷ Ω·m28.3 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.08 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Brazeability / Solderability
Polishability
Same in both: Castability 40 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Same in both: Typical Recycled Content 60%
Strength versus weight
Yield strength against density for every stainless steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
305 Annealed vs 305 Cold Drawn — frequently asked
Is 305 Cold Drawn stronger than 305 Annealed?
Yes. 305 Cold Drawn has a typical yield strength of 430 MPa (62.4 ksi) against 260 MPa (37.7 ksi) for 305 Annealed — about 65% more. Tensile strength is 655 MPa (95 ksi) vs 585 MPa (84.8 ksi).
Which condition does FabDigit quote by default, Annealed or Cold Drawn?
Annealed is the default 305 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 305 Annealed or 305 Cold Drawn?
305 Cold Drawn, by a small margin. Both rate fair for machinability — 45/100 against 38/100 for 305 Annealed.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 305 Annealed and 305 Cold Drawn side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.