Stainless Steel 1.4980-CD vs 1.4980-ST
Stainless Steel · 1.4980 temper comparison
1.4980-CD and 1.4980-ST are two conditions of the same stainless steel grade, 1.4980: CD (cold drawn) versus ST (solution annealed). The chemistry is identical, so every difference below comes from the condition. 1.4980-CD is the stronger of the two: yield strength 690 MPa (100 ksi) against 310 MPa (45 ksi) for 1.4980-ST, about 123% more; tensile strength follows at 900 MPa (131 ksi) vs 690 MPa (100 ksi). In exchange, 1.4980-ST is the more ductile: elongation 45% versus 20% for 1.4980-CD, and 1.4980-CD is harder (255 HB vs 170 HB). 1.4980-ST runs hotter in service (600°C vs 500°C continuous). On the shop floor, 1.4980-ST welds better (good vs fair).
1.4980-CDChoose it when strength drives the design.
1.4980-STChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
1.4980-CD vs 1.4980-ST: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Shear Modulus 77 GPa11.2 Msi · Bulk Modulus 176 GPa25.5 Msi · Poisson's Ratio 0.31
Physical
Density and transition temperatures.
Same in both: Density 7.92 g/cm³0.29 lb/in³ · Melting Point (Solidus) 1,370°C2,498 °F · Liquidus Temperature 1,430°C2,606 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 12.6 W/m·K7.3 BTU/hr·ft·°F · Specific Heat Capacity 460 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 16.4 µm/m·K9.1 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Min Service Temperature -253°C-423 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 1.9 % IACS · Electrical Resistivity 9.1×10⁻⁷ Ω·m35.8 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.1 V · Corrosion Resistance 60 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 55 / 100 · Polishability 75 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 80 MJ/kg34,394 BTU/lb · Embodied Carbon (primary production) 5.8 kg CO₂/kg · Embodied Water 120 L/kg14.4 gal/lb · Typical Recycled Content 35%
Strength versus weight
Yield strength against density for every stainless steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
1.4980-CD vs 1.4980-ST — frequently asked
Is 1.4980-CD stronger than 1.4980-ST?
Yes. 1.4980-CD has a typical yield strength of 690 MPa (100 ksi) against 310 MPa (45 ksi) for 1.4980-ST — about 123% more. Tensile strength is 900 MPa (131 ksi) vs 690 MPa (100 ksi).
Which condition does FabDigit quote by default, CD or ST?
STA is the default 1.4980 condition in the FabDigit quote flow (neither CD nor ST). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which welds better, 1.4980-CD or 1.4980-ST?
1.4980-ST. Its weldability rates good (60/100) against fair (45/100) for 1.4980-CD.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 1.4980-CD and 1.4980-ST side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.