Stainless Steel 1.4905-AW vs 1.4905-N
Stainless Steel · 1.4905 temper comparison
1.4905-AW and 1.4905-N are two conditions of the same stainless steel grade, 1.4905: AW (as-welded deposit) versus N (normalized). The chemistry is identical, so every difference below comes from the condition. 1.4905-N is the stronger of the two: yield strength 900 MPa (131 ksi) against 800 MPa (116 ksi) for 1.4905-AW, about 13% more; tensile strength follows at 1,250 MPa (181 ksi) vs 1,000 MPa (145 ksi). 1.4905-N is harder — 400 HB against 375 HB for 1.4905-AW — which matters for wear surfaces and threads. 1.4905-AW runs hotter in service (600°C vs 450°C continuous).
1.4905-AWChoose it when the part sees heat.
1.4905-NChoose it when strength drives the design, or when surface hardness matters.
1.4905-AW vs 1.4905-N: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 216 GPa31.3 Msi · Shear Modulus 84 GPa12.2 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.3 · Elongation at Break 10% · Reduction in Area 35%
Physical
Density and transition temperatures.
Same in both: Density 7.75 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,420°C2,588 °F · Liquidus Temperature 1,490°C2,714 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 460 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 10.8 µm/m·K6 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Min Service Temperature -20°C-4 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 2.8 % IACS · Electrical Resistivity 6.2×10⁻⁷ Ω·m24.4 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.4 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Same in both: Formability (cold) 5 / 100 · Brazeability / Solderability 30 / 100 · Polishability 55 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 36 MJ/kg15,477 BTU/lb · Embodied Carbon (primary production) 2.9 kg CO₂/kg · Embodied Water 70 L/kg8.4 gal/lb · Typical Recycled Content 40%
Strength versus weight
Yield strength against density for every stainless steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
1.4905-AW vs 1.4905-N — frequently asked
Is 1.4905-N stronger than 1.4905-AW?
Yes. 1.4905-N has a typical yield strength of 900 MPa (131 ksi) against 800 MPa (116 ksi) for 1.4905-AW — about 13% more. Tensile strength is 1,250 MPa (181 ksi) vs 1,000 MPa (145 ksi).
Which condition does FabDigit quote by default, AW or N?
NT is the default 1.4905 condition in the FabDigit quote flow (neither AW nor N). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which welds better, 1.4905-AW or 1.4905-N?
1.4905-AW. Its weldability rates poor (25/100) against poor (20/100) for 1.4905-N.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 1.4905-AW and 1.4905-N side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.