Stainless Steel 1.4887 CAST-S vs 1.4887-CD
Stainless Steel · 1.4887 temper comparison
1.4887 CAST-S and 1.4887-CD are two conditions of the same stainless steel grade, 1.4887: CAST-S (as-Cast, statically (sand/investment) cast) versus CD (cold drawn). The chemistry is identical, so every difference below comes from the condition. 1.4887-CD is the stronger of the two: yield strength 420 MPa (60.9 ksi) against 230 MPa (33.4 ksi) for 1.4887 CAST-S, about 83% more; tensile strength follows at 680 MPa (98.6 ksi) vs 450 MPa (65.3 ksi). 1.4887-CD is the more ductile: elongation 20% versus 10% for 1.4887 CAST-S, and 1.4887-CD is harder (215 HB vs 180 HB). 1.4887-CD is stiffer (190 GPa vs 180 GPa). On the shop floor, 1.4887-CD welds better (good vs fair).
1.4887-CDChoose it when strength drives the design, or when the part is bent, formed or impact-loaded.
1.4887 CAST-S vs 1.4887-CD: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Shear Modulus 73 GPa10.6 Msi · Bulk Modulus 158 GPa22.9 Msi · Poisson's Ratio 0.3
Physical
Density and transition temperatures.
Same in both: Density 7.9 g/cm³0.29 lb/in³ · Melting Point (Solidus) 1,340°C2,444 °F · Liquidus Temperature 1,400°C2,552 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 13 W/m·K7.5 BTU/hr·ft·°F · Specific Heat Capacity 500 J/kg·K0.12 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 15.5 µm/m·K8.6 µin/in·°F · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 1.7 % IACS · Electrical Resistivity 1.02×10⁻⁶ Ω·m40.2 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 75 / 100 · Brazeability / Solderability 45 / 100 · Polishability 60 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 72 MJ/kg30,954 BTU/lb · Embodied Carbon (primary production) 6 kg CO₂/kg · Embodied Water 220 L/kg26.4 gal/lb · Typical Recycled Content 45%
Strength versus weight
Yield strength against density for every stainless steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
1.4887 CAST-S vs 1.4887-CD — frequently asked
Is 1.4887-CD stronger than 1.4887 CAST-S?
Yes. 1.4887-CD has a typical yield strength of 420 MPa (60.9 ksi) against 230 MPa (33.4 ksi) for 1.4887 CAST-S — about 83% more. Tensile strength is 680 MPa (98.6 ksi) vs 450 MPa (65.3 ksi).
Which condition does FabDigit quote by default, CAST-S or CD?
SA is the default 1.4887 condition in the FabDigit quote flow (neither CAST-S nor CD). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 1.4887 CAST-S or 1.4887-CD?
1.4887-CD, by a small margin. Both rate poor for machinability — 27/100 against 18/100 for 1.4887 CAST-S; for welding the order is 1.4887-CD first (good, 55/100) then 1.4887 CAST-S (fair, 45/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 1.4887 CAST-S and 1.4887-CD side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.