Refractory Metal Pure Mo As Rolled vs Pure Mo Sintered
Refractory Metal · Pure Mo temper comparison
Pure Mo As Rolled and Pure Mo Sintered are two conditions of the same refractory metal grade, Pure Mo: As Rolled (hot rolled) versus Sintered. The chemistry is identical, so every difference below comes from the condition. Pure Mo As Rolled is the stronger of the two: yield strength 590 MPa (85.6 ksi) against 300 MPa (43.5 ksi) for Pure Mo Sintered, about 97% more; tensile strength follows at 700 MPa (102 ksi) vs 400 MPa (58 ksi). Pure Mo As Rolled is the more ductile: elongation 10% versus 5% for Pure Mo Sintered, and Pure Mo As Rolled is harder (240 HB vs 160 HB). Pure Mo As Rolled is stiffer (320 GPa vs 290 GPa).
Pure Mo As RolledChoose it when strength drives the design, or when the part is bent, formed or impact-loaded.
Pure Mo As Rolled vs Pure Mo Sintered: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all refractory metal grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all refractory metal grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Pure Mo As RolledPure Mo Sintered
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Shear Modulus 125 GPa18.1 Msi · Bulk Modulus 230 GPa33.4 Msi · Poisson's Ratio 0.31
Physical
Density and transition temperatures.
Density
Same in both: Melting Point (Solidus) 2,623°C4,753 °F · Liquidus Temperature 2,623°C4,753 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Same in both: Specific Heat Capacity 250 J/kg·K0.06 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 5.2 µm/m·K2.9 µin/in·°F · Latent Heat of Fusion 390 J/g168 BTU/lb · Max Service Temperature (continuous) 500°C932 °F · Min Service Temperature 20°C68 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.2 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 70 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 380 MJ/kg163,371 BTU/lb · Embodied Carbon (primary production) 25 kg CO₂/kg · Embodied Water 300 L/kg35.9 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every refractory metal grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Pure Mo As Rolled vs Pure Mo Sintered — frequently asked
Is Pure Mo As Rolled stronger than Pure Mo Sintered?
Yes. Pure Mo As Rolled has a typical yield strength of 590 MPa (85.6 ksi) against 300 MPa (43.5 ksi) for Pure Mo Sintered — about 97% more. Tensile strength is 700 MPa (102 ksi) vs 400 MPa (58 ksi).
Which condition does FabDigit quote by default, As Rolled or Sintered?
As Rolled is the default Pure Mo condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, Pure Mo As Rolled or Pure Mo Sintered?
Pure Mo Sintered, by a small margin. Both rate fair for machinability — 45/100 against 40/100 for Pure Mo As Rolled; for welding the order is Pure Mo As Rolled first (poor, 20/100) then Pure Mo Sintered (poor, 15/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in Pure Mo As Rolled and Pure Mo Sintered side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.