Precious Metal AgC10 vs AgCdO12
Precious Metal · grade comparison
Precious Metal AgC10 and AgCdO12 are both precious metal grades. AgCdO12 is the stronger of the two: yield strength 200 MPa (29 ksi) against 70 MPa (10.2 ksi) for AgC10, about 186% more; tensile strength follows at 270 MPa (39.2 ksi) vs 110 MPa (16 ksi). AgCdO12 is the more ductile: elongation 12% versus 4% for AgC10, and AgCdO12 is harder (80 HB vs 30 HB). AgC10 is lighter (7.6 g/cm³ vs 10.2 g/cm³ for AgCdO12) and AgCdO12 is stiffer (80 GPa vs 55 GPa). On the shop floor, AgCdO12 welds better (25 vs 15 out of 100).
AgC10Choose it when weight is the constraint, or when the part sees heat.
AgCdO12Choose it when strength drives the design, or when the part is bent, formed or impact-loaded.
AgC10 vs AgCdO12: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all precious metal grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all precious metal grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Poisson's Ratio
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Compressive Strength
Hardness, Brinell
Shear Modulus
Bulk Modulus
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Hardness, Rockwell B
Hardness, Vickers
Physical
Density and transition temperatures.
Density
Melting Point (Solidus)
Liquidus Temperature
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Thermal Expansion (CTE, 20–100 °C)
Latent Heat of Fusion
Max Service Temperature (continuous)
Min Service Temperature
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) 0.1 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Weldability
Formability (cold)
Brazeability / Solderability
Polishability
Machinability Rating (AISI 1212 = 100 %)
Castability
Same in both: Machinability 55 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Carbon (primary production)
Typical Recycled Content
Embodied Water
Same in both: Embodied Energy (primary production) 1,300 MJ/kg558,900 BTU/lb
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Modulus of Resilience
Thermal Diffusivity
Thermal Shock Resistance Index
Strength versus weight
Yield strength against density for every precious metal grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | AgC10 | AgCdO12 |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$$$ High | $$$$ High |
| Min. machined wall | — | — |
| Best machined surface | — | — |
AgC10 vs AgCdO12 — frequently asked
Is AgCdO12 stronger than AgC10?
Yes. AgCdO12 has a typical yield strength of 200 MPa (29 ksi) against 70 MPa (10.2 ksi) for AgC10 — about 186% more. Tensile strength is 270 MPa (39.2 ksi) vs 110 MPa (16 ksi).
Which is cheaper, AgC10 or AgCdO12?
Both sit in the same relative cost tier ($$$$, high); the part price will be decided by machining time, tolerance and quantity rather than by the material.
Which welds better, AgC10 or AgCdO12?
AgCdO12. Its weldability rates poor (25/100) against poor (15/100) for AgC10.
Ready to make it?
Upload a CAD file and FabDigit prices the part in AgC10 and AgCdO12 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.