GF Nylon-Like vs PC-Like
Polyurethane · grade comparison
GF Nylon-Like and PC-Like are both polyurethane grades, both rigid pu. PC-Like is the more ductile: elongation 9% versus 5% for GF Nylon-Like. PC-Like is lighter (1.16 g/cm³ vs 1.4 g/cm³ for GF Nylon-Like) and GF Nylon-Like is stiffer (4 GPa vs 2.7 GPa).
GF Nylon-LikeChoose it when the part sees heat.
PC-LikeChoose it when the part is bent, formed or impact-loaded, or when weight is the constraint.
GF Nylon-Like vs PC-Like: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all polyurethane grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all polyurethane grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Elongation at Break
Compressive Strength
Flexural Modulus
Izod Impact, Notched
Hardness, Rockwell R
Shear Modulus
Bulk Modulus
Yield Strength (0.2% offset)
Compressive Modulus
Shear Strength
Hardness, Rockwell M
Same in both: Poisson's Ratio 0.38 · Tensile Strength (Ultimate) 60 MPa8.7 ksi · Flexural Strength 92 MPa13.3 ksi · Hardness, Shore D 85 Shore D
Physical
Density and transition temperatures.
Density
Glass Transition (Tg)
Water Absorption (24 h)
Refractive Index
Light Transmission
Same in both: Water Absorption (Saturation) 1.2%
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Thermal Expansion (CTE, 20–100 °C)
Max Service Temperature (continuous)
Min Service Temperature
Heat Deflection Temp. @ 0.45 MPa
Heat Deflection Temp. @ 1.8 MPa
Limiting Oxygen Index
Max Service Temperature (short-term)
Electrical
Conductivity and insulation.
Dielectric Strength
Dielectric Constant (1 MHz)
Surface Resistivity
Same in both: Electrical Resistivity 1×10¹² Ω·m3.94×10¹⁹ µΩ·in · Dissipation Factor (1 MHz) 0.03 · Volume Resistivity 1×10¹⁴ Ω·cm
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: UV / Weathering Resistance 25 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Polishability
Mold Shrinkage
Mold Temperature (typ.)
Weldability
Formability (cold)
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Same in both: Typical Recycled Content 0%
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Thermal Diffusivity
Same in both: Thermal Shock Resistance Index 0
Strength versus weight
Yield strength against density for every polyurethane grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | GF Nylon-Like | PC-Like |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$ Standard | $$ Standard |
| Min. machined wall | — | — |
| Best machined surface | — | — |
Both are offered for Urethane casting.
GF Nylon-Like vs PC-Like — frequently asked
What is the difference between GF Nylon-Like and PC-Like?
GF Nylon-Like and PC-Like are both polyurethane grades, both rigid pu. PC-Like is the more ductile: elongation 9% versus 5% for GF Nylon-Like. PC-Like is lighter (1.16 g/cm³ vs 1.4 g/cm³ for GF Nylon-Like) and GF Nylon-Like is stiffer (4 GPa vs 2.7 GPa).
Which is cheaper, GF Nylon-Like or PC-Like?
Both sit in the same relative cost tier ($$, standard); the part price will be decided by machining time, tolerance and quantity rather than by the material.
When should I choose GF Nylon-Like over PC-Like?
Pick GF Nylon-Like when the part sees heat. Pick PC-Like when the part is bent, formed or impact-loaded, or when weight is the constraint.
Ready to make it?
Upload a CAD file and FabDigit prices the part in GF Nylon-Like and PC-Like side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.