Nickel Alloy N06110-CD vs N06110 CW-HS
Nickel Alloy · N06110 temper comparison
N06110-CD and N06110 CW-HS are two conditions of the same nickel alloy grade, N06110: CD (cold drawn) versus CW-HS (heavily Cold Worked, high strength). The chemistry is identical, so every difference below comes from the condition. N06110 CW-HS is the stronger of the two: yield strength 1,100 MPa (160 ksi) against 830 MPa (120 ksi) for N06110-CD, about 33% more; tensile strength follows at 1,250 MPa (181 ksi) vs 1,000 MPa (145 ksi). In exchange, N06110-CD is the more ductile: elongation 22% versus 12% for N06110 CW-HS, and N06110 CW-HS is harder (370 HB vs 300 HB). N06110-CD runs hotter in service (540°C vs 480°C continuous).
N06110-CDChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
N06110 CW-HSChoose it when strength drives the design.
N06110-CD vs N06110 CW-HS: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Same in both: Elastic (Young's) Modulus 210 GPa30.5 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 175 GPa25.4 Msi · Poisson's Ratio 0.31 · Hardness, Rockwell B 93 HRB
Physical
Density and transition temperatures.
Same in both: Density 8.4 g/cm³0.3 lb/in³ · Melting Point (Solidus) 1,330°C2,426 °F · Liquidus Temperature 1,380°C2,516 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 9 W/m·K5.2 BTU/hr·ft·°F · Specific Heat Capacity 430 J/kg·K0.1 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.3 µm/m·K6.8 µin/in·°F · Latent Heat of Fusion 290 J/g125 BTU/lb · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.1 V · Corrosion Resistance 88 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 35 / 100 · Brazeability / Solderability 55 / 100 · Polishability 75 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 150 MJ/kg64,488 BTU/lb · Embodied Carbon (primary production) 13 kg CO₂/kg · Embodied Water 250 L/kg30 gal/lb · Typical Recycled Content 35%
Strength versus weight
Yield strength against density for every nickel alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
N06110-CD vs N06110 CW-HS — frequently asked
Is N06110 CW-HS stronger than N06110-CD?
Yes. N06110 CW-HS has a typical yield strength of 1,100 MPa (160 ksi) against 830 MPa (120 ksi) for N06110-CD — about 33% more. Tensile strength is 1,250 MPa (181 ksi) vs 1,000 MPa (145 ksi).
Which condition does FabDigit quote by default, CD or CW-HS?
SA is the default N06110 condition in the FabDigit quote flow (neither CD nor CW-HS). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which welds better, N06110-CD or N06110 CW-HS?
N06110-CD. Its weldability rates good (60/100) against good (55/100) for N06110 CW-HS.
Ready to make it?
Upload a CAD file and FabDigit prices the part in N06110-CD and N06110 CW-HS side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.