Nickel Alloy ENi-1 vs ERNiMo-7
Nickel Alloy · grade comparison
Nickel Alloy ENi-1 and ERNiMo-7 are both nickel alloy grades. ERNiMo-7 is the stronger of the two: yield strength 470 MPa (68.2 ksi) against 250 MPa (36.3 ksi) for ENi-1, about 88% more; tensile strength follows at 780 MPa (113 ksi) vs 440 MPa (63.8 ksi). ERNiMo-7 is the more ductile: elongation 35% versus 30% for ENi-1, and ERNiMo-7 is harder (205 HB vs 100 HB). ENi-1 is lighter (8.9 g/cm³ vs 9.22 g/cm³ for ERNiMo-7) and ERNiMo-7 is stiffer (217 GPa vs 200 GPa). On the shop floor, ENi-1 machines more easily (fair vs poor).
ENi-1Choose it when weight is the constraint, or when the part is machined in volume.
ERNiMo-7Choose it when strength drives the design, or when the part is bent, formed or impact-loaded.
ENi-1 vs ERNiMo-7: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Shear Modulus
Bulk Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Hardness, Rockwell C
Same in both: Poisson's Ratio 0.31 · Reduction in Area 40%
Physical
Density and transition temperatures.
Density
Melting Point (Solidus)
Liquidus Temperature
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Thermal Expansion (CTE, 20–100 °C)
Latent Heat of Fusion
Same in both: Max Service Temperature (continuous) 400°C752 °F · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Galvanic Potential (seawater, vs SCE)
Corrosion Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Brazeability / Solderability
Polishability
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Same in both: Typical Recycled Content 25%
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Modulus of Resilience
Thermal Diffusivity
Thermal Shock Resistance Index
Strength versus weight
Yield strength against density for every nickel alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | ENi-1 | ERNiMo-7 |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$$$ High | $$$$ High |
| Min. machined wall | — | — |
| Best machined surface | — | — |
Both take the same 3 finishes: Gold Plating, Plasma Spray, Silver Plating.
ENi-1 vs ERNiMo-7 — frequently asked
Is ERNiMo-7 stronger than ENi-1?
Yes. ERNiMo-7 has a typical yield strength of 470 MPa (68.2 ksi) against 250 MPa (36.3 ksi) for ENi-1 — about 88% more. Tensile strength is 780 MPa (113 ksi) vs 440 MPa (63.8 ksi).
Which is cheaper, ENi-1 or ERNiMo-7?
Both sit in the same relative cost tier ($$$$, high); the part price will be decided by machining time, tolerance and quantity rather than by the material.
Which is easier to machine, ENi-1 or ERNiMo-7?
ENi-1. Its machinability rates fair (42/100) against poor (16/100) for ERNiMo-7; for welding the order is ENi-1 first (excellent, 85/100) then ERNiMo-7 (very good, 78/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in ENi-1 and ERNiMo-7 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.