Nickel Alloy ENi-1 vs ERNiCrFe-6
Nickel Alloy · grade comparison
Nickel Alloy ENi-1 and ERNiCrFe-6 are both nickel alloy grades. ERNiCrFe-6 is the stronger of the two: yield strength 410 MPa (59.5 ksi) against 250 MPa (36.3 ksi) for ENi-1, about 64% more; tensile strength follows at 655 MPa (95 ksi) vs 440 MPa (63.8 ksi). ERNiCrFe-6 is the more ductile: elongation 35% versus 30% for ENi-1, and ERNiCrFe-6 is harder (185 HB vs 100 HB). ERNiCrFe-6 is lighter (8.2 g/cm³ vs 8.9 g/cm³ for ENi-1) and ERNiCrFe-6 runs hotter in service (950°C vs 400°C continuous). On the shop floor, ENi-1 machines more easily (fair vs poor).
ENi-1Choose it when the part is machined in volume.
ERNiCrFe-6Choose it when strength drives the design, or when the part is bent, formed or impact-loaded.
ENi-1 vs ERNiCrFe-6: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Shear Modulus
Bulk Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Poisson's Ratio 0.31 · Reduction in Area 40%
Physical
Density and transition temperatures.
Density
Melting Point (Solidus)
Liquidus Temperature
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Latent Heat of Fusion
Max Service Temperature (continuous)
Same in both: Thermal Expansion (CTE, 20–100 °C) 13.3 µm/m·K7.4 µin/in·°F · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Galvanic Potential (seawater, vs SCE)
Corrosion Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Brazeability / Solderability
Same in both: Weldability 85 / 100 · Formability (cold) 60 / 100 · Polishability 60 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Typical Recycled Content
Embodied Water
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Modulus of Resilience
Thermal Diffusivity
Thermal Shock Resistance Index
Strength versus weight
Yield strength against density for every nickel alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | ENi-1 | ERNiCrFe-6 |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$$$ High | $$$$ High |
| Min. machined wall | — | — |
| Best machined surface | — | — |
Both take the same 3 finishes: Gold Plating, Plasma Spray, Silver Plating.
ENi-1 vs ERNiCrFe-6 — frequently asked
Is ERNiCrFe-6 stronger than ENi-1?
Yes. ERNiCrFe-6 has a typical yield strength of 410 MPa (59.5 ksi) against 250 MPa (36.3 ksi) for ENi-1 — about 64% more. Tensile strength is 655 MPa (95 ksi) vs 440 MPa (63.8 ksi).
Which is cheaper, ENi-1 or ERNiCrFe-6?
Both sit in the same relative cost tier ($$$$, high); the part price will be decided by machining time, tolerance and quantity rather than by the material.
Which is easier to machine, ENi-1 or ERNiCrFe-6?
ENi-1. Its machinability rates fair (42/100) against poor (18/100) for ERNiCrFe-6.
Ready to make it?
Upload a CAD file and FabDigit prices the part in ENi-1 and ERNiCrFe-6 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.