Nickel Alloy CY5SnBiM vs CZ-100
Nickel Alloy · grade comparison
Nickel Alloy CY5SnBiM and CZ-100 are both nickel alloy grades. CY5SnBiM is the stronger of the two: yield strength 200 MPa (29 ksi) against 160 MPa (23.2 ksi) for CZ-100, about 25% more. In exchange, CZ-100 is the more ductile: elongation 25% versus 18% for CY5SnBiM, and CY5SnBiM is harder (130 HB vs 110 HB). CZ-100 is stiffer (180 GPa vs 150 GPa) and CZ-100 runs hotter in service (480°C vs 425°C continuous). On the shop floor, CY5SnBiM machines more easily (good vs fair) and CZ-100 welds better (good vs poor).
CY5SnBiMChoose it when strength drives the design, or when the part is machined in volume.
CZ-100Choose it when the part is bent, formed or impact-loaded, or when the part sees heat.
CY5SnBiM vs CZ-100: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Shear Modulus
Bulk Modulus
Poisson's Ratio
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Compressive Strength
Physical
Density and transition temperatures.
Density
Melting Point (Solidus)
Liquidus Temperature
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Thermal Expansion (CTE, 20–100 °C)
Latent Heat of Fusion
Max Service Temperature (continuous)
Min Service Temperature
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Galvanic Potential (seawater, vs SCE)
Corrosion Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Castability
Brazeability / Solderability
Same in both: Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Same in both: Typical Recycled Content 40%
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Modulus of Resilience
Thermal Diffusivity
Thermal Shock Resistance Index
Strength versus weight
Yield strength against density for every nickel alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | CY5SnBiM | CZ-100 |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$$$ High | $$$$ High |
| Min. machined wall | — | — |
| Best machined surface | — | — |
Both take the same 3 finishes: Gold Plating, Plasma Spray, Silver Plating.
CY5SnBiM vs CZ-100 — frequently asked
Is CY5SnBiM stronger than CZ-100?
Yes. CY5SnBiM has a typical yield strength of 200 MPa (29 ksi) against 160 MPa (23.2 ksi) for CZ-100 — about 25% more. Tensile strength is 390 MPa (56.6 ksi) vs 380 MPa (55.1 ksi).
Which is cheaper, CY5SnBiM or CZ-100?
Both sit in the same relative cost tier ($$$$, high); the part price will be decided by machining time, tolerance and quantity rather than by the material.
Which is easier to machine, CY5SnBiM or CZ-100?
CY5SnBiM. Its machinability rates good (55/100) against fair (35/100) for CZ-100; for welding the order is CZ-100 first (good, 60/100) then CY5SnBiM (poor, 25/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in CY5SnBiM and CZ-100 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.