Copper Alloy CC383H-GS vs CC383H-SR
Copper Alloy · CC383H temper comparison
CC383H-GS and CC383H-SR are two conditions of the same copper alloy grade, CC383H: GS (sand cast, as-cast) versus SR (stress relieved). The chemistry is identical, so every difference below comes from the condition. CC383H-GS is the stronger of the two: yield strength 290 MPa (42.1 ksi) against 270 MPa (39.2 ksi) for CC383H-SR, about 7% more. In exchange, CC383H-SR is the more ductile: elongation 25% versus 22% for CC383H-GS, and CC383H-GS is harder (140 HB vs 130 HB).
CC383H-GSChoose it when strength drives the design.
CC383H-SRChoose it when the part is bent, formed or impact-loaded.
CC383H-GS vs CC383H-SR: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 150 GPa21.8 Msi · Shear Modulus 57 GPa8.3 Msi · Bulk Modulus 132 GPa19.1 Msi · Poisson's Ratio 0.31
Physical
Density and transition temperatures.
Same in both: Density 8.9 g/cm³0.32 lb/in³ · Melting Point (Solidus) 1,170°C2,138 °F · Liquidus Temperature 1,240°C2,264 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Same in both: Specific Heat Capacity 377 J/kg·K0.09 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 15.8 µm/m·K8.8 µin/in·°F · Max Service Temperature (continuous) 300°C572 °F · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.27 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 62 / 100 · Brazeability / Solderability 70 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 90 MJ/kg38,693 BTU/lb · Embodied Carbon (primary production) 5.6 kg CO₂/kg · Embodied Water 300 L/kg35.9 gal/lb · Typical Recycled Content 35%
Strength versus weight
Yield strength against density for every copper alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
CC383H-GS vs CC383H-SR — frequently asked
Is CC383H-GS stronger than CC383H-SR?
Yes. CC383H-GS has a typical yield strength of 290 MPa (42.1 ksi) against 270 MPa (39.2 ksi) for CC383H-SR — about 7% more. Tensile strength is 480 MPa (69.6 ksi) vs 470 MPa (68.2 ksi).
Which condition does FabDigit quote by default, GS or SR?
GS is the default CC383H condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which welds better, CC383H-GS or CC383H-SR?
CC383H-SR. Its weldability rates excellent (85/100) against very good (80/100) for CC383H-GS.
Ready to make it?
Upload a CAD file and FabDigit prices the part in CC383H-GS and CC383H-SR side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.