Copper Alloy C63000-M10 vs C63000-M30
Copper Alloy · C63000 temper comparison
C63000-M10 and C63000-M30 are two conditions of the same copper alloy grade, C63000: M10 (as hot forged and air cooled) versus M30 (as hot extruded). The chemistry is identical, so every difference below comes from the condition. C63000-M10 is the stronger of the two: yield strength 380 MPa (55.1 ksi) against 345 MPa (50 ksi) for C63000-M30, about 10% more. In exchange, C63000-M30 is the more ductile: elongation 20% versus 13% for C63000-M10, and C63000-M10 is harder (197 HB vs 170 HB).
C63000-M10Choose it when strength drives the design.
C63000-M30Choose it when the part is bent, formed or impact-loaded.
C63000-M10 vs C63000-M30: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Bulk Modulus
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Same in both: Elastic (Young's) Modulus 117 GPa17 Msi · Shear Modulus 44 GPa6.4 Msi · Poisson's Ratio 0.32 · Tensile Strength (Ultimate) 690 MPa100 ksi
Physical
Density and transition temperatures.
Melting Point (Solidus)
Same in both: Density 7.58 g/cm³0.27 lb/in³ · Liquidus Temperature 1,054°C1,929 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Same in both: Thermal Expansion (CTE, 20–100 °C) 16.2 µm/m·K9 µin/in·°F · Latent Heat of Fusion 210 J/g90.3 BTU/lb · Max Service Temperature (continuous) 300°C572 °F · Min Service Temperature -200°C-328 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 7 % IACS · Electrical Resistivity 2.46×10⁻⁷ Ω·m9.69 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Galvanic Potential (seawater, vs SCE)
Same in both: Corrosion Resistance 78 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Brazeability / Solderability
Same in both: Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Typical Recycled Content
Strength versus weight
Yield strength against density for every copper alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
C63000-M10 vs C63000-M30 — frequently asked
Is C63000-M10 stronger than C63000-M30?
Yes. C63000-M10 has a typical yield strength of 380 MPa (55.1 ksi) against 345 MPa (50 ksi) for C63000-M30 — about 10% more. Tensile strength is 690 MPa (100 ksi) vs 690 MPa (100 ksi).
Which condition does FabDigit quote by default, M10 or M30?
HR50 is the default C63000 condition in the FabDigit quote flow (neither M10 nor M30). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose C63000-M10 over C63000-M30?
Pick C63000-M10 when strength drives the design. Pick C63000-M30 when the part is bent, formed or impact-loaded.
Ready to make it?
Upload a CAD file and FabDigit prices the part in C63000-M10 and C63000-M30 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.