6061/SiC/10p vs 6092/SiC/17.5p
Composite · grade comparison
6061/SiC/10p and 6092/SiC/17.5p are both composite grades. 6092/SiC/17.5p is the stronger of the two: yield strength 434 MPa (62.9 ksi) against 296 MPa (42.9 ksi) for 6061/SiC/10p, about 47% more; tensile strength follows at 483 MPa (70.1 ksi) vs 338 MPa (49 ksi). 6092/SiC/17.5p is stiffer (100 GPa vs 81 GPa) and 6061/SiC/10p runs hotter in service (175°C vs 150°C continuous).
6061/SiC/10pChoose it when the part sees heat.
6092/SiC/17.5pChoose it when strength drives the design.
6061/SiC/10p vs 6092/SiC/17.5p: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all composite grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all composite grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Shear Modulus
Poisson's Ratio
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Compressive Strength
Compressive Modulus
Flexural Strength
Flexural Modulus
Shear Strength
Fracture Toughness (K_IC)
Same in both: Bulk Modulus 79 GPa11.5 Msi · Elongation at Break 6%
Physical
Density and transition temperatures.
Density
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Thermal Expansion (CTE, 20–100 °C)
Max Service Temperature (continuous)
Min Service Temperature
Max Service Temperature (short-term)
Electrical
Conductivity and insulation.
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Corrosion Resistance 55 / 100 · UV / Weathering Resistance 95 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Polishability
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Typical Recycled Content
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Modulus of Resilience
Thermal Diffusivity
Thermal Shock Resistance Index
Strength versus weight
Yield strength against density for every composite grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | 6061/SiC/10p | 6092/SiC/17.5p |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$$$ High | $$$$ High |
| Min. machined wall | — | — |
| Best machined surface | — | — |
6061/SiC/10p vs 6092/SiC/17.5p — frequently asked
Is 6092/SiC/17.5p stronger than 6061/SiC/10p?
Yes. 6092/SiC/17.5p has a typical yield strength of 434 MPa (62.9 ksi) against 296 MPa (42.9 ksi) for 6061/SiC/10p — about 47% more. Tensile strength is 483 MPa (70.1 ksi) vs 338 MPa (49 ksi).
Which is cheaper, 6061/SiC/10p or 6092/SiC/17.5p?
Both sit in the same relative cost tier ($$$$, high); the part price will be decided by machining time, tolerance and quantity rather than by the material.
Which is easier to machine, 6061/SiC/10p or 6092/SiC/17.5p?
6061/SiC/10p, by a small margin. Both rate poor for machinability — 30/100 against 22/100 for 6092/SiC/17.5p.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 6061/SiC/10p and 6092/SiC/17.5p side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.