Aluminum BAlSi-4-AW vs BAlSi-4-F
Aluminum · BAlSi-4 temper comparison
BAlSi-4-AW and BAlSi-4-F are two conditions of the same aluminum grade, BAlSi-4: AW (as-welded deposit) versus F (as fabricated). The chemistry is identical, so every difference below comes from the condition. BAlSi-4-AW is the stronger of the two: yield strength 80 MPa (11.6 ksi) against 75 MPa (10.9 ksi) for BAlSi-4-F, about 7% more; tensile strength follows at 170 MPa (24.7 ksi) vs 160 MPa (23.2 ksi). BAlSi-4-AW is the more ductile: elongation 4% versus 3% for BAlSi-4-F.
BAlSi-4-AWChoose it when strength drives the design, or when the part is bent, formed or impact-loaded.
BAlSi-4-AW vs BAlSi-4-F: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Same in both: Shear Modulus 27 GPa3.9 Msi · Bulk Modulus 73 GPa10.6 Msi · Poisson's Ratio 0.33 · Hardness, Brinell 55 HB · Hardness, Vickers 60 HV
Physical
Density and transition temperatures.
Same in both: Density 2.66 g/cm³0.1 lb/in³ · Melting Point (Solidus) 577°C1,071 °F · Liquidus Temperature 582°C1,080 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Same in both: Specific Heat Capacity 900 J/kg·K0.21 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 20.4 µm/m·K11.3 µin/in·°F · Latent Heat of Fusion 500 J/g215 BTU/lb · Max Service Temperature (continuous) 150°C302 °F · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.83 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Formability (cold)
Same in both: Machinability 30 / 100 · Machinability Rating (AISI 1212 = 100 %) 30% · Weldability 85 / 100 · Castability 95 / 100 · Brazeability / Solderability 98 / 100 · Polishability 40 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 205 MJ/kg88,134 BTU/lb · Embodied Carbon (primary production) 12.5 kg CO₂/kg · Embodied Water 1,100 L/kg132 gal/lb · Typical Recycled Content 20%
Strength versus weight
Yield strength against density for every aluminum grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
BAlSi-4-AW vs BAlSi-4-F — frequently asked
Is BAlSi-4-AW stronger than BAlSi-4-F?
Yes. BAlSi-4-AW has a typical yield strength of 80 MPa (11.6 ksi) against 75 MPa (10.9 ksi) for BAlSi-4-F — about 7% more. Tensile strength is 170 MPa (24.7 ksi) vs 160 MPa (23.2 ksi).
Which condition does FabDigit quote by default, AW or F?
AW is the default BAlSi-4 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose BAlSi-4-AW over BAlSi-4-F?
Pick BAlSi-4-AW when strength drives the design, or when the part is bent, formed or impact-loaded.
Ready to make it?
Upload a CAD file and FabDigit prices the part in BAlSi-4-AW and BAlSi-4-F side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.