Aluminum AC8B-F vs AC8B-T6
Aluminum · AC8B temper comparison
AC8B-F and AC8B-T6 are two conditions of the same aluminum grade, AC8B: F (as fabricated) versus T6 (solution heat treated and artificially aged). The chemistry is identical, so every difference below comes from the condition. AC8B-T6 is the stronger of the two: yield strength 235 MPa (34.1 ksi) against 130 MPa (18.9 ksi) for AC8B-F, about 81% more; tensile strength follows at 280 MPa (40.6 ksi) vs 180 MPa (26.1 ksi). In exchange, AC8B-F is the more ductile: elongation 1.5% versus 1% for AC8B-T6, and AC8B-T6 is harder (110 HB vs 85 HB). AC8B-T6 runs hotter in service (230°C vs 200°C continuous) and AC8B-F conducts electricity better (28 % IACS vs 25 % IACS).
AC8B-FChoose it when the part is bent, formed or impact-loaded.
AC8B-T6Choose it when strength drives the design, or when the part sees heat.
AC8B-F vs AC8B-T6: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Shear Strength
Fatigue Strength (Endurance Limit)
Hardness, Brinell
Same in both: Elastic (Young's) Modulus 82 GPa11.9 Msi · Shear Modulus 31 GPa4.5 Msi · Bulk Modulus 73 GPa10.6 Msi · Poisson's Ratio 0.33 · Compressive Strength 260 MPa37.7 ksi · Fracture Toughness (K_IC) 15 MPa·√m13.7 ksi·√in · Charpy V-Notch Impact (RT) 3 J2.2 ft·lbf
Physical
Density and transition temperatures.
Same in both: Density 2.76 g/cm³0.1 lb/in³ · Melting Point (Solidus) 521°C970 °F · Liquidus Temperature 582°C1,080 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 963 J/kg·K0.23 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 20.7 µm/m·K11.5 µin/in·°F · Latent Heat of Fusion 389 J/g167 BTU/lb · Min Service Temperature -60°C-76 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Same in both: Electrical Resistivity 6.6×10⁻⁸ Ω·m2.6 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.78 V · Corrosion Resistance 38 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Same in both: Machinability Rating (AISI 1212 = 100 %) 200% · Weldability 22 / 100 · Castability 85 / 100 · Brazeability / Solderability 20 / 100 · Polishability 40 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 200 MJ/kg85,985 BTU/lb · Embodied Carbon (primary production) 12 kg CO₂/kg · Embodied Water 1,100 L/kg132 gal/lb · Typical Recycled Content 75%
Strength versus weight
Yield strength against density for every aluminum grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
AC8B-F vs AC8B-T6 — frequently asked
Is AC8B-T6 stronger than AC8B-F?
Yes. AC8B-T6 has a typical yield strength of 235 MPa (34.1 ksi) against 130 MPa (18.9 ksi) for AC8B-F — about 81% more. Tensile strength is 280 MPa (40.6 ksi) vs 180 MPa (26.1 ksi).
Which condition does FabDigit quote by default, F or T6?
T6 is the default AC8B condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, AC8B-F or AC8B-T6?
AC8B-F. Its machinability rates good (55/100) against fair (50/100) for AC8B-T6.
Ready to make it?
Upload a CAD file and FabDigit prices the part in AC8B-F and AC8B-T6 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.