Aluminum 7017-T4 vs 7017-T651
Aluminum · 7017 temper comparison
7017-T4 and 7017-T651 are two conditions of the same aluminum grade, 7017: T4 (solution heat treated and naturally aged) versus T651 (T6, stress relieved by stretching). The chemistry is identical, so every difference below comes from the condition. 7017-T651 is the stronger of the two: yield strength 390 MPa (56.6 ksi) against 250 MPa (36.3 ksi) for 7017-T4, about 56% more; tensile strength follows at 455 MPa (66 ksi) vs 380 MPa (55.1 ksi). In exchange, 7017-T4 is the more ductile: elongation 16% versus 11% for 7017-T651, and 7017-T651 is harder (138 HB vs 105 HB). 7017-T651 runs hotter in service (120°C vs 100°C continuous).
7017-T4Choose it when the part is bent, formed or impact-loaded.
7017-T651Choose it when strength drives the design, or when the part sees heat.
7017-T4 vs 7017-T651: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Shear Strength
Fatigue Strength (Endurance Limit)
Hardness, Brinell
Same in both: Elastic (Young's) Modulus 70 GPa10.2 Msi · Shear Modulus 26.5 GPa3.8 Msi · Bulk Modulus 69 GPa10 Msi · Poisson's Ratio 0.33 · Fracture Toughness (K_IC) 32 MPa·√m29.1 ksi·√in · Hardness, Vickers 150 HV
Physical
Density and transition temperatures.
Same in both: Density 2.78 g/cm³0.1 lb/in³ · Melting Point (Solidus) 590°C1,094 °F · Liquidus Temperature 640°C1,184 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 140 W/m·K80.9 BTU/hr·ft·°F · Specific Heat Capacity 875 J/kg·K0.21 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 23.4 µm/m·K13 µin/in·°F · Latent Heat of Fusion 390 J/g168 BTU/lb · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Same in both: Electrical Resistivity 5.4×10⁻⁸ Ω·m2.13 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.87 V · Corrosion Resistance 45 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Formability (cold)
Same in both: Machinability Rating (AISI 1212 = 100 %) 70% · Weldability 72 / 100 · Castability 30 / 100 · Brazeability / Solderability 20 / 100 · Polishability 55 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 200 MJ/kg85,985 BTU/lb · Embodied Carbon (primary production) 12.5 kg CO₂/kg · Embodied Water 1,200 L/kg144 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every aluminum grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
7017-T4 vs 7017-T651 — frequently asked
Is 7017-T651 stronger than 7017-T4?
Yes. 7017-T651 has a typical yield strength of 390 MPa (56.6 ksi) against 250 MPa (36.3 ksi) for 7017-T4 — about 56% more. Tensile strength is 455 MPa (66 ksi) vs 380 MPa (55.1 ksi).
Which condition does FabDigit quote by default, T4 or T651?
Specify the condition in the material field or the drawing note; FabDigit prices the quote for the state you call out.
Which is easier to machine, 7017-T4 or 7017-T651?
7017-T651, by a small margin. Both rate good for machinability — 68/100 against 60/100 for 7017-T4.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 7017-T4 and 7017-T651 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.