Aluminum 5050-H112 vs 5050-H32
Aluminum · 5050 temper comparison
5050-H112 and 5050-H32 are two conditions of the same aluminum grade, 5050: H112 (strain hardened from hot working only) versus H32 (strain hardened and stabilized, quarter hard). The chemistry is identical, so every difference below comes from the condition. 5050-H32 is the stronger of the two: yield strength 145 MPa (21 ksi) against 70 MPa (10.2 ksi) for 5050-H112, about 107% more; tensile strength follows at 170 MPa (24.7 ksi) vs 150 MPa (21.8 ksi). In exchange, 5050-H112 is the more ductile: elongation 20% versus 9% for 5050-H32, and 5050-H32 is harder (46 HB vs 38 HB). 5050-H112 runs hotter in service (200°C vs 150°C continuous).
5050-H112Choose it when the part is bent, formed or impact-loaded, or when the part sees heat.
5050-H32Choose it when strength drives the design.
5050-H112 vs 5050-H32: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Shear Strength
Fatigue Strength (Endurance Limit)
Hardness, Brinell
Same in both: Elastic (Young's) Modulus 68.9 GPa10 Msi · Shear Modulus 25.9 GPa3.8 Msi · Bulk Modulus 75 GPa10.9 Msi · Poisson's Ratio 0.33
Physical
Density and transition temperatures.
Same in both: Density 2.69 g/cm³0.1 lb/in³ · Melting Point (Solidus) 627°C1,161 °F · Liquidus Temperature 652°C1,206 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 900 J/kg·K0.21 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 23.8 µm/m·K13.2 µin/in·°F · Latent Heat of Fusion 397 J/g171 BTU/lb · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.83 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 35 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 200 MJ/kg85,985 BTU/lb · Embodied Carbon (primary production) 12 kg CO₂/kg · Embodied Water 1,200 L/kg144 gal/lb · Typical Recycled Content 35%
Strength versus weight
Yield strength against density for every aluminum grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
5050-H112 vs 5050-H32 — frequently asked
Is 5050-H32 stronger than 5050-H112?
Yes. 5050-H32 has a typical yield strength of 145 MPa (21 ksi) against 70 MPa (10.2 ksi) for 5050-H112 — about 107% more. Tensile strength is 170 MPa (24.7 ksi) vs 150 MPa (21.8 ksi).
Which condition does FabDigit quote by default, H112 or H32?
Specify the condition in the material field or the drawing note; FabDigit prices the quote for the state you call out.
Which is easier to machine, 5050-H112 or 5050-H32?
5050-H32. Its machinability rates fair (40/100) against poor (33/100) for 5050-H112.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 5050-H112 and 5050-H32 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.