Aluminum 332.0-T5 vs 332.0-T6
Aluminum · 332.0 temper comparison
332.0-T5 and 332.0-T6 are two conditions of the same aluminum grade, 332.0: T5 (cooled from hot working and artificially aged) versus T6 (solution heat treated and artificially aged). The chemistry is identical, so every difference below comes from the condition. 332.0-T6 is the stronger of the two: yield strength 240 MPa (34.8 ksi) against 193 MPa (28 ksi) for 332.0-T5, about 24% more; tensile strength follows at 285 MPa (41.3 ksi) vs 248 MPa (36 ksi). In exchange, 332.0-T5 is the more ductile: elongation 1% versus 0.8% for 332.0-T6, and 332.0-T6 is harder (125 HB vs 105 HB). 332.0-T5 runs hotter in service (250°C vs 200°C continuous).
332.0-T5Choose it when the part is bent, formed or impact-loaded, or when the part sees heat.
332.0-T6Choose it when strength drives the design.
332.0-T5 vs 332.0-T6: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Hardness, Brinell
Same in both: Elastic (Young's) Modulus 76 GPa11 Msi · Shear Modulus 28 GPa4.1 Msi · Bulk Modulus 75 GPa10.9 Msi · Poisson's Ratio 0.33
Physical
Density and transition temperatures.
Same in both: Density 2.76 g/cm³0.1 lb/in³ · Melting Point (Solidus) 521°C970 °F · Liquidus Temperature 582°C1,080 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 963 J/kg·K0.23 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 20.6 µm/m·K11.4 µin/in·°F · Latent Heat of Fusion 389 J/g167 BTU/lb · Min Service Temperature -195°C-319 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.79 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Weldability
Formability (cold)
Same in both: Castability 85 / 100 · Brazeability / Solderability 15 / 100 · Polishability 40 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 45 MJ/kg19,347 BTU/lb · Embodied Carbon (primary production) 3.5 kg CO₂/kg · Embodied Water 300 L/kg35.9 gal/lb · Typical Recycled Content 85%
Strength versus weight
Yield strength against density for every aluminum grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
332.0-T5 vs 332.0-T6 — frequently asked
Is 332.0-T6 stronger than 332.0-T5?
Yes. 332.0-T6 has a typical yield strength of 240 MPa (34.8 ksi) against 193 MPa (28 ksi) for 332.0-T5 — about 24% more. Tensile strength is 285 MPa (41.3 ksi) vs 248 MPa (36 ksi).
Which condition does FabDigit quote by default, T5 or T6?
T5 is the default 332.0 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which welds better, 332.0-T5 or 332.0-T6?
332.0-T5. Its weldability rates poor (25/100) against poor (20/100) for 332.0-T6.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 332.0-T5 and 332.0-T6 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.