Aluminum 2014-H111 vs 2014-T351
Aluminum · 2014 temper comparison
2014-H111 and 2014-T351 are two conditions of the same aluminum grade, 2014: H111 (slightly strain hardened) versus T351 (T3, stress relieved by stretching). The chemistry is identical, so every difference below comes from the condition. 2014-T351 is the stronger of the two: yield strength 295 MPa (42.8 ksi) against 105 MPa (15.2 ksi) for 2014-H111, about 181% more; tensile strength follows at 440 MPa (63.8 ksi) vs 190 MPa (27.6 ksi). 2014-T351 is harder — 105 HB against 47 HB for 2014-H111 — which matters for wear surfaces and threads. 2014-H111 runs hotter in service (150°C vs 120°C continuous) and 2014-H111 conducts heat better (190 W/m·K vs 134 W/m·K). On the shop floor, 2014-T351 machines more easily (very good vs fair) and 2014-H111 forms better (very good vs fair).
2014-H111Choose it when the part sees heat.
2014-T351Choose it when strength drives the design, or when surface hardness matters.
2014-H111 vs 2014-T351: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Hardness, Brinell
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 72.4 GPa10.5 Msi · Shear Modulus 28 GPa4.1 Msi · Bulk Modulus 71 GPa10.3 Msi · Poisson's Ratio 0.33
Physical
Density and transition temperatures.
Same in both: Density 2.8 g/cm³0.1 lb/in³ · Melting Point (Solidus) 507°C945 °F · Liquidus Temperature 638°C1,180 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 880 J/kg·K0.21 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 22.8 µm/m·K12.7 µin/in·°F · Latent Heat of Fusion 385 J/g166 BTU/lb · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Galvanic Potential (seawater, vs SCE)
Corrosion Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Polishability
Same in both: Castability 25 / 100 · Brazeability / Solderability 15 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 155 MJ/kg66,638 BTU/lb · Embodied Carbon (primary production) 11.5 kg CO₂/kg · Embodied Water 1,200 L/kg144 gal/lb · Typical Recycled Content 20%
Strength versus weight
Yield strength against density for every aluminum grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
2014-H111 vs 2014-T351 — frequently asked
Is 2014-T351 stronger than 2014-H111?
Yes. 2014-T351 has a typical yield strength of 295 MPa (42.8 ksi) against 105 MPa (15.2 ksi) for 2014-H111 — about 181% more. Tensile strength is 440 MPa (63.8 ksi) vs 190 MPa (27.6 ksi).
Which condition does FabDigit quote by default, H111 or T351?
Specify the condition in the material field or the drawing note; FabDigit prices the quote for the state you call out.
Which is easier to machine, 2014-H111 or 2014-T351?
2014-T351. Its machinability rates very good (75/100) against fair (45/100) for 2014-H111; for welding the order is 2014-H111 first (poor, 25/100) then 2014-T351 (poor, 20/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 2014-H111 and 2014-T351 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.