Titanium Ti Grade 30 Annealed vs Ti Grade 30 AS-WELDED
Titanium · Ti Grade 30 temper comparison
Ti Grade 30 Annealed and Ti Grade 30 AS-WELDED are two conditions of the same titanium grade, Ti Grade 30: Annealed versus AS-WELDED (as-welded deposit). The chemistry is identical, so every difference below comes from the condition. Ti Grade 30 AS-WELDED is the stronger of the two: yield strength 350 MPa (50.8 ksi) against 330 MPa (47.9 ksi) for Ti Grade 30 Annealed, about 6% more. In exchange, Ti Grade 30 Annealed is the more ductile: elongation 28% versus 20% for Ti Grade 30 AS-WELDED, and Ti Grade 30 AS-WELDED is harder (175 HB vs 160 HB).
Ti Grade 30 AnnealedChoose it when the part is bent, formed or impact-loaded.
Ti Grade 30 AS-WELDEDChoose it when strength drives the design.
Ti Grade 30 Annealed vs Ti Grade 30 AS-WELDED: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all titanium grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all titanium grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Ti Grade 30 AnnealedTi Grade 30 AS-WELDED
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 105 GPa15.2 Msi · Shear Modulus 45 GPa6.5 Msi · Bulk Modulus 110 GPa16 Msi · Poisson's Ratio 0.34
Physical
Density and transition temperatures.
Same in both: Density 4.51 g/cm³0.16 lb/in³ · Melting Point (Solidus) 1,650°C3,002 °F · Liquidus Temperature 1,665°C3,029 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 16.5 W/m·K9.5 BTU/hr·ft·°F · Specific Heat Capacity 523 J/kg·K0.12 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 8.6 µm/m·K4.8 µin/in·°F · Latent Heat of Fusion 320 J/g138 BTU/lb · Max Service Temperature (continuous) 300°C572 °F · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 3.1 % IACS · Electrical Resistivity 5.6×10⁻⁷ Ω·m22 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.05 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Formability (cold)
Same in both: Weldability 85 / 100 · Castability 40 / 100 · Brazeability / Solderability 40 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 700 MJ/kg300,946 BTU/lb · Embodied Carbon (primary production) 44 kg CO₂/kg · Embodied Water 700 L/kg83.9 gal/lb · Typical Recycled Content 20%
Strength versus weight
Yield strength against density for every titanium grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Ti Grade 30 Annealed vs Ti Grade 30 AS-WELDED — frequently asked
Is Ti Grade 30 AS-WELDED stronger than Ti Grade 30 Annealed?
Yes. Ti Grade 30 AS-WELDED has a typical yield strength of 350 MPa (50.8 ksi) against 330 MPa (47.9 ksi) for Ti Grade 30 Annealed — about 6% more. Tensile strength is 450 MPa (65.3 ksi) vs 440 MPa (63.8 ksi).
Which condition does FabDigit quote by default, Annealed or AS-WELDED?
Annealed is the default Ti Grade 30 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, Ti Grade 30 Annealed or Ti Grade 30 AS-WELDED?
Ti Grade 30 Annealed. Its machinability rates fair (35/100) against poor (30/100) for Ti Grade 30 AS-WELDED.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Ti Grade 30 Annealed and Ti Grade 30 AS-WELDED side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.