Titanium PT-7M-M vs PT-7M-SR
Titanium · PT-7M temper comparison
PT-7M-M and PT-7M-SR are two conditions of the same titanium grade, PT-7M: M (thermomechanically controlled processed) versus SR (stress relieved). The chemistry is identical, so every difference below comes from the condition. PT-7M-SR is the stronger of the two: yield strength 470 MPa (68.2 ksi) against 370 MPa (53.7 ksi) for PT-7M-M, about 27% more; tensile strength follows at 570 MPa (82.7 ksi) vs 500 MPa (72.5 ksi). In exchange, PT-7M-M is the more ductile: elongation 25% versus 18% for PT-7M-SR, and PT-7M-SR is harder (180 HB vs 160 HB). PT-7M-M runs hotter in service (350°C vs 320°C continuous).
PT-7M-MChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
PT-7M-SRChoose it when strength drives the design.
PT-7M-M vs PT-7M-SR: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all titanium grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all titanium grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 105 GPa15.2 Msi · Shear Modulus 40 GPa5.8 Msi · Bulk Modulus 110 GPa16 Msi · Poisson's Ratio 0.34
Physical
Density and transition temperatures.
Same in both: Density 4.49 g/cm³0.16 lb/in³ · Melting Point (Solidus) 1,620°C2,948 °F · Liquidus Temperature 1,670°C3,038 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 13.5 W/m·K7.8 BTU/hr·ft·°F · Specific Heat Capacity 540 J/kg·K0.13 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 8.6 µm/m·K4.8 µin/in·°F · Latent Heat of Fusion 390 J/g168 BTU/lb · Min Service Temperature -253°C-423 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 3 % IACS · Electrical Resistivity 5.8×10⁻⁷ Ω·m22.8 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.1 V · Corrosion Resistance 88 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 35 / 100 · Brazeability / Solderability 40 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 600 MJ/kg257,954 BTU/lb · Embodied Carbon (primary production) 35 kg CO₂/kg · Embodied Water 400 L/kg47.9 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every titanium grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
PT-7M-M vs PT-7M-SR — frequently asked
Is PT-7M-SR stronger than PT-7M-M?
Yes. PT-7M-SR has a typical yield strength of 470 MPa (68.2 ksi) against 370 MPa (53.7 ksi) for PT-7M-M — about 27% more. Tensile strength is 570 MPa (82.7 ksi) vs 500 MPa (72.5 ksi).
Which condition does FabDigit quote by default, M or SR?
M is the default PT-7M condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose PT-7M-M over PT-7M-SR?
Pick PT-7M-M when the part is bent, formed or impact-loaded, or when the part sees heat. Pick PT-7M-SR when strength drives the design.
Ready to make it?
Upload a CAD file and FabDigit prices the part in PT-7M-M and PT-7M-SR side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.