Steel T5-ANN vs T5 HT-65
Steel · T5 temper comparison
T5-ANN and T5 HT-65 are two conditions of the same steel grade, T5: ANN (annealed) versus HT-65 (hardened & tempered 65–66 HRC). The chemistry is identical, so every difference below comes from the condition. T5 HT-65 is the stronger of the two: yield strength 1,950 MPa (283 ksi) against 590 MPa (85.6 ksi) for T5-ANN, about 3.3 times as much; tensile strength follows at 2,050 MPa (297 ksi) vs 900 MPa (131 ksi). In exchange, T5-ANN is the more ductile: elongation 12% versus 0.3% for T5 HT-65, and T5 HT-65 is harder (865 HV vs 268 HV). T5 HT-65 runs hotter in service (600°C vs 400°C continuous) and T5-ANN conducts heat better (22 W/m·K vs 19 W/m·K). On the shop floor, T5-ANN machines more easily (poor vs not recommended) and T5-ANN welds better (poor vs not recommended).
T5-ANNChoose it when the part is bent, formed or impact-loaded, or when the part is machined in volume.
T5 HT-65Choose it when strength drives the design, or when the part sees heat.
T5-ANN vs T5 HT-65: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Vickers
Same in both: Shear Modulus 83 GPa12 Msi · Bulk Modulus 165 GPa23.9 Msi · Poisson's Ratio 0.29 · Hardness, Brinell 255 HB · Hardness, Rockwell B 100 HRB
Physical
Density and transition temperatures.
Same in both: Density 8.75 g/cm³0.32 lb/in³ · Melting Point (Solidus) 1,400°C2,552 °F · Liquidus Temperature 1,480°C2,696 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 420 J/kg·K0.1 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 11 µm/m·K6.1 µin/in·°F · Latent Heat of Fusion 250 J/g107 BTU/lb · Min Service Temperature -50°C-58 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.55 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 25 / 100 · Brazeability / Solderability 55 / 100 · Polishability 60 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 100 MJ/kg42,992 BTU/lb · Embodied Carbon (primary production) 7 kg CO₂/kg · Embodied Water 130 L/kg15.6 gal/lb · Typical Recycled Content 35%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
T5-ANN vs T5 HT-65 — frequently asked
Is T5 HT-65 stronger than T5-ANN?
Yes. T5 HT-65 has a typical yield strength of 1,950 MPa (283 ksi) against 590 MPa (85.6 ksi) for T5-ANN — about 3.3 times as much. Tensile strength is 2,050 MPa (297 ksi) vs 900 MPa (131 ksi).
Which condition does FabDigit quote by default, ANN or HT-65?
ANN is the default T5 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, T5-ANN or T5 HT-65?
T5-ANN. Its machinability rates poor (32/100) against not recommended (5/100) for T5 HT-65; for welding the order is T5-ANN first (poor, 15/100) then T5 HT-65 (not recommended, 5/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in T5-ANN and T5 HT-65 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.