Steel SUP9 Cold Drawn vs SUP9 Hot Rolled
Steel · SUP9 temper comparison
SUP9 Cold Drawn and SUP9 Hot Rolled are two conditions of the same steel grade, SUP9: Cold Drawn versus Hot Rolled. The chemistry is identical, so every difference below comes from the condition. SUP9 Cold Drawn is the stronger of the two: yield strength 720 MPa (104 ksi) against 570 MPa (82.7 ksi) for SUP9 Hot Rolled, about 26% more. In exchange, SUP9 Hot Rolled is the more ductile: elongation 13% versus 10% for SUP9 Cold Drawn, and SUP9 Hot Rolled is harder (280 HB vs 265 HB). SUP9 Cold Drawn runs hotter in service (300°C vs 250°C continuous). On the shop floor, SUP9 Cold Drawn machines more easily (good vs fair).
SUP9 Cold DrawnChoose it when strength drives the design, or when the part sees heat.
SUP9 Hot RolledChoose it when the part is bent, formed or impact-loaded.
SUP9 Cold Drawn vs SUP9 Hot Rolled: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
SUP9 Cold DrawnSUP9 Hot Rolled
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Shear Modulus 79 GPa11.5 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29 · Reduction in Area 35%
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,420°C2,588 °F · Liquidus Temperature 1,490°C2,714 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 46 W/m·K26.6 BTU/hr·ft·°F · Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.3 µm/m·K6.8 µin/in·°F · Latent Heat of Fusion 250 J/g107 BTU/lb · Min Service Temperature -40°C-40 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 7.8 % IACS · Electrical Resistivity 2.2×10⁻⁷ Ω·m8.66 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.62 V · Corrosion Resistance 11 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Same in both: Formability (cold) 30 / 100 · Brazeability / Solderability 50 / 100 · Polishability 60 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 26 MJ/kg11,178 BTU/lb · Embodied Carbon (primary production) 2 kg CO₂/kg · Embodied Water 55 L/kg6.6 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
SUP9 Cold Drawn vs SUP9 Hot Rolled — frequently asked
Is SUP9 Cold Drawn stronger than SUP9 Hot Rolled?
Yes. SUP9 Cold Drawn has a typical yield strength of 720 MPa (104 ksi) against 570 MPa (82.7 ksi) for SUP9 Hot Rolled — about 26% more. Tensile strength is 900 MPa (131 ksi) vs 950 MPa (138 ksi).
Which condition does FabDigit quote by default, Cold Drawn or Hot Rolled?
Annealed is the default SUP9 condition in the FabDigit quote flow (neither Cold Drawn nor Hot Rolled). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, SUP9 Cold Drawn or SUP9 Hot Rolled?
SUP9 Cold Drawn. Its machinability rates good (58/100) against fair (45/100) for SUP9 Hot Rolled.
Ready to make it?
Upload a CAD file and FabDigit prices the part in SUP9 Cold Drawn and SUP9 Hot Rolled side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.