Steel SNCM625-N vs SNCM625 QT-28-32HRC
Steel · SNCM625 temper comparison
SNCM625-N and SNCM625 QT-28-32HRC are two conditions of the same steel grade, SNCM625: N (normalized) versus QT-28-32HRC. The chemistry is identical, so every difference below comes from the condition. SNCM625 QT-28-32HRC is the stronger of the two: yield strength 860 MPa (125 ksi) against 640 MPa (92.8 ksi) for SNCM625-N, about 34% more; tensile strength follows at 990 MPa (144 ksi) vs 930 MPa (135 ksi). SNCM625 QT-28-32HRC is the more ductile: elongation 20% versus 18% for SNCM625-N, and SNCM625 QT-28-32HRC is harder (285 HB vs 270 HB).
SNCM625 QT-28-32HRCChoose it when strength drives the design, or when the part is bent, formed or impact-loaded.
SNCM625-N vs SNCM625 QT-28-32HRC: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 206 GPa29.9 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,425°C2,597 °F · Liquidus Temperature 1,495°C2,723 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.3 µm/m·K6.8 µin/in·°F · Latent Heat of Fusion 260 J/g112 BTU/lb · Min Service Temperature -60°C-76 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.6 V · Corrosion Resistance 13 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 45 / 100 · Polishability 65 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 34 MJ/kg14,617 BTU/lb · Embodied Carbon (primary production) 2.4 kg CO₂/kg · Embodied Water 60 L/kg7.2 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
SNCM625-N vs SNCM625 QT-28-32HRC — frequently asked
Is SNCM625 QT-28-32HRC stronger than SNCM625-N?
Yes. SNCM625 QT-28-32HRC has a typical yield strength of 860 MPa (125 ksi) against 640 MPa (92.8 ksi) for SNCM625-N — about 34% more. Tensile strength is 990 MPa (144 ksi) vs 930 MPa (135 ksi).
Which condition does FabDigit quote by default, N or QT-28-32HRC?
QT is the default SNCM625 condition in the FabDigit quote flow (neither N nor QT-28-32HRC). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which welds better, SNCM625-N or SNCM625 QT-28-32HRC?
SNCM625-N. Its weldability rates poor (30/100) against poor (22/100) for SNCM625 QT-28-32HRC.
Ready to make it?
Upload a CAD file and FabDigit prices the part in SNCM625-N and SNCM625 QT-28-32HRC side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.