Steel SCM435-HR vs SCM435 Q&T
Steel · SCM435 temper comparison
SCM435-HR and SCM435 Q&T are two conditions of the same steel grade, SCM435: HR (hot rolled) versus Q&T (quenched and tempered). The chemistry is identical, so every difference below comes from the condition. SCM435 Q&T is the stronger of the two: yield strength 850 MPa (123 ksi) against 450 MPa (65.3 ksi) for SCM435-HR, about 89% more; tensile strength follows at 1,000 MPa (145 ksi) vs 700 MPa (102 ksi). In exchange, SCM435-HR is the more ductile: elongation 20% versus 17% for SCM435 Q&T, and SCM435 Q&T is harder (293 HB vs 207 HB). On the shop floor, SCM435-HR machines more easily (good vs fair) and SCM435-HR welds better (45 vs 35 out of 100).
SCM435-HRChoose it when the part is bent, formed or impact-loaded, or when the part is machined in volume.
SCM435 Q&TChoose it when strength drives the design.
SCM435-HR vs SCM435 Q&T: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 207 GPa30 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29 · Hardness, Rockwell B 94 HRB
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,416°C2,581 °F · Liquidus Temperature 1,495°C2,723 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 42 W/m·K24.3 BTU/hr·ft·°F · Specific Heat Capacity 473 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.3 µm/m·K6.8 µin/in·°F · Latent Heat of Fusion 250 J/g107 BTU/lb · Max Service Temperature (continuous) 400°C752 °F · Min Service Temperature -40°C-40 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 7.8 % IACS · Electrical Resistivity 2.2×10⁻⁷ Ω·m8.66 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.6 V · Corrosion Resistance 13 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 55 / 100 · Polishability 65 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 29 MJ/kg12,468 BTU/lb · Embodied Carbon (primary production) 2.1 kg CO₂/kg · Embodied Water 45 L/kg5.4 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
SCM435-HR vs SCM435 Q&T — frequently asked
Is SCM435 Q&T stronger than SCM435-HR?
Yes. SCM435 Q&T has a typical yield strength of 850 MPa (123 ksi) against 450 MPa (65.3 ksi) for SCM435-HR — about 89% more. Tensile strength is 1,000 MPa (145 ksi) vs 700 MPa (102 ksi).
Which condition does FabDigit quote by default, HR or Q&T?
HR is the default SCM435 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, SCM435-HR or SCM435 Q&T?
SCM435-HR. Its machinability rates good (55/100) against fair (45/100) for SCM435 Q&T; for welding the order is SCM435-HR first (fair, 45/100) then SCM435 Q&T (fair, 35/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in SCM435-HR and SCM435 Q&T side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.