Steel S420NL +N vs S420NL +N 100-150
Steel · S420NL temper comparison
S420NL +N and S420NL +N 100-150 are two conditions of the same steel grade, S420NL: +N (normalized) versus +N 100-150 (+N). The chemistry is identical, so every difference below comes from the condition. S420NL +N is the stronger of the two: yield strength 450 MPa (65.3 ksi) against 370 MPa (53.7 ksi) for S420NL +N 100-150, about 22% more; tensile strength follows at 580 MPa (84.1 ksi) vs 530 MPa (76.9 ksi). S420NL +N is harder — 175 HB against 158 HB for S420NL +N 100-150 — which matters for wear surfaces and threads. On the shop floor, S420NL +N forms better (65 vs 55 out of 100).
S420NL +NChoose it when strength drives the design, or when surface hardness matters.
S420NL +N vs S420NL +N 100-150: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 210 GPa30.5 Msi · Shear Modulus 81 GPa11.7 Msi · Bulk Modulus 165 GPa23.9 Msi · Poisson's Ratio 0.3
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,500°C2,732 °F · Liquidus Temperature 1,520°C2,768 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 44 W/m·K25.4 BTU/hr·ft·°F · Specific Heat Capacity 460 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12 µm/m·K6.7 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Max Service Temperature (continuous) 350°C662 °F · Min Service Temperature -50°C-58 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 8.2 % IACS · Electrical Resistivity 2.1×10⁻⁷ Ω·m8.27 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.62 V · Corrosion Resistance 12 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 60 / 100 · Polishability 45 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 26 MJ/kg11,178 BTU/lb · Embodied Carbon (primary production) 2.1 kg CO₂/kg · Embodied Water 40 L/kg4.8 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
S420NL +N vs S420NL +N 100-150 — frequently asked
Is S420NL +N stronger than S420NL +N 100-150?
Yes. S420NL +N has a typical yield strength of 450 MPa (65.3 ksi) against 370 MPa (53.7 ksi) for S420NL +N 100-150 — about 22% more. Tensile strength is 580 MPa (84.1 ksi) vs 530 MPa (76.9 ksi).
Which condition does FabDigit quote by default, +N or +N 100-150?
+N is the default S420NL condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which welds better, S420NL +N or S420NL +N 100-150?
S420NL +N. Its weldability rates excellent (85/100) against very good (80/100) for S420NL +N 100-150.
Ready to make it?
Upload a CAD file and FabDigit prices the part in S420NL +N and S420NL +N 100-150 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.