Steel Q355D-CD vs Q355D-M
Steel · Q355D temper comparison
Q355D-CD and Q355D-M are two conditions of the same steel grade, Q355D: CD (cold drawn) versus M (thermomechanically controlled processed). The chemistry is identical, so every difference below comes from the condition. Q355D-CD is the stronger of the two: yield strength 500 MPa (72.5 ksi) against 400 MPa (58 ksi) for Q355D-M, about 25% more; tensile strength follows at 620 MPa (89.9 ksi) vs 520 MPa (75.4 ksi). In exchange, Q355D-M is the more ductile: elongation 26% versus 14% for Q355D-CD, and Q355D-CD is harder (185 HB vs 150 HB). Q355D-M runs hotter in service (380°C vs 300°C continuous). On the shop floor, Q355D-M welds better (excellent vs very good).
Q355D-CDChoose it when strength drives the design.
Q355D-MChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
Q355D-CD vs Q355D-M: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 210 GPa30.5 Msi · Shear Modulus 81 GPa11.7 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.28
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,450°C2,642 °F · Liquidus Temperature 1,515°C2,759 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 46 W/m·K26.6 BTU/hr·ft·°F · Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12 µm/m·K6.7 µin/in·°F · Latent Heat of Fusion 250 J/g107 BTU/lb · Min Service Temperature -20°C-4 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 8.6 % IACS · Electrical Resistivity 2×10⁻⁷ Ω·m7.87 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.62 V · Corrosion Resistance 12 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 55 / 100 · Polishability 45 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 25 MJ/kg10,748 BTU/lb · Embodied Carbon (primary production) 2 kg CO₂/kg · Embodied Water 40 L/kg4.8 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Q355D-CD vs Q355D-M — frequently asked
Is Q355D-CD stronger than Q355D-M?
Yes. Q355D-CD has a typical yield strength of 500 MPa (72.5 ksi) against 400 MPa (58 ksi) for Q355D-M — about 25% more. Tensile strength is 620 MPa (89.9 ksi) vs 520 MPa (75.4 ksi).
Which condition does FabDigit quote by default, CD or M?
HR is the default Q355D condition in the FabDigit quote flow (neither CD nor M). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which welds better, Q355D-CD or Q355D-M?
Q355D-M. Its weldability rates excellent (93/100) against very good (80/100) for Q355D-CD.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Q355D-CD and Q355D-M side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.